Cequent Towing Products 36477 Instructions D'installation

Frame rail
Hitch Shown In Proper Position
Equipment Required: Pull wires (provided)
Lubricant or Soapy water, hacksaw
Fastener Kit 36477F
Wrenches: M10, 13, 18, 19, 11/16 &
3/4
A. Insert bolt and
B. Align block on
access hole
block into frame
Figure 4
Reverse pull wire procedure
Remove this
end
1" [25.4mm]
Figure 2
j
Qty. (2) Carriage bolt, 7/16-14 X 1.75 GR5
k
Qty. (2) Spacer (small)
l
Qty. (2) Conical washer, 7/16
m
Qty. (2) Hex nut, 7/16-14
n
Qty. (2) Hex bolt M12 X 1.75 X 45 CL10.9
1. Lower exhaust by removing (3) rubber isolators, one behind rear axle. Be careful not to allow mufflers to fall under their own weight. Note:
Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
2. Remove exhaust hanger bracket on each side. Return fasteners to owner. Modify driver side exhaust bracket as shown in Figure 2.
3. Feed 7/16 (item 1 & 2) spacers and carriage bolts into position using the pull wires provided (both rail). Leave pull wire attached. See
Figure 3.
Feed 1/2 carriage bolt and spacer (Item 8 & 9) using the reverse pull wire procedure on driver's side. Leave pull wire attached. See Figure 4.
4.
5. Raise hitch into position, over the exhaust and align with carriage bolts Feed pull wires thru adjacent holes in the hitch, remove pull wires
and attach conical washers and nuts, finger tight only (Be careful not to push fastener back into frame rail).
6. Reattach exhaust hanger brackets as shown in Figure 1 using fasteners provided with hitch.
7. Tighten all fasteners to the required torque specification.
8. Raise exhaust back into position and reattach to rubber isolators.
Tighten all M8 CL9.8 fasteners with torque wrench to 25 Lb.-Ft. (34 N*M). Tighten all M12 CL10.9 fasteners with torque wrench to 80 Lb.-Ft. (108 N*M).
Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M). Tighten all ½-13 Gr5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2012 Cequent Towing Products
Installation Instructions
Lincoln MKS
Fascia
Drawbar Kit:
36051
Drawbar must be used in
the Rise position only.
Figure 3
Example of pull wire procedure
C. Pull bolt thru
block
Existing
weldnuts
Remove this
end
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Frame rail
j
k
q
r
l
m
o
p
s
o
Qty. (3) Conical washer 1/2
p
Qty. (2) Bolt, M8 X 1.25 X 55 CL9.8
q
Qty. (1) Carriage bolt, 1/2-13 X 1.75 Gr5
r
Qty. (1) Spacer (large)
s
Qty. (1) Hex nut 1/2-13
36477N
Part Numbers:
36477, 90192,
06663
j
k
l
m
Access
hole
o
o
n
n
Exhaust hanger
bracket
1-11-12
Form F206 Rev A 5605
Existing
weldnuts
Access
hole
Exhaust
hanger
bracket
Figure
1
Rev. B