Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36379F
Wrenches: ¾, Torque Wrench
Drill Bits: ½"
7
Figure 2.
1
Qty. (2)
Carriage Bolt ½-13 X 2.00 Gr5
2
Qty. (2)
Block ¼" x 1-1/2" x 3.00 Lg.
3
Qty. (4)
Conical Toothed Washer ½
4
Qty. (2)
Hex Nut, ½-13
5
Qty. (2)
Hex Bolt, ½-13 x 1.25" LG.
1.
Raise Hitch into position, aligning the top holes in the Upright Brackets with the existing holes in vehicle end panel.
Note: The Upright Bracket goes on the Forward side of the end panel.
2.
Loosely install the ½" x 1-1/4" lg. hex bolts and conical toothed washers thru hole in Hitch and end panel into the handle nut assemblies.
3.
Using the Hitch as a template, drill the forward attachment holes for the side arm bars into the bottom of the frame rails.
Note: The driver's side has an existing hole in bottom of frame to align with slot in the side arm.
4.
Fishwire carriage bolt and block through the forward access hole in the bottom of frame rail and through ½" drilled hole and slot in hitch
side arm. NOTE: The fuel filler tube may have to be lowered temporarily to gain proper clearance to access hole on the passenger's side
frame rail.
5.
Loosely install conical toothed washers and hex nuts onto carriage bolts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Chevrolet Malibu Maxx
Drawbar Kit:
Fascia
36071
Drawbar must be used in the
RISE position only.
Access Hole
Tighten ½-13 GR5 Handle Nut fasteners with torque wrench to 50 Lb.-Ft.
Tighten ½-13 GR5 Carriage Bolt fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
3500 LB Max Gross Trailer Weight
300 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
Frame Rail
Drilled Hole
Figure 1.
6
Qty. (2)
Handle Nut Assembly, ½"
Qty. (1)
Pull Wire
7
Sheet 1 of 3
36379N
Part Numbers:
Manufacturer's Rating or
End Panel
10-4-05
36379
06388
90136
1
2
3
4
6
3
5
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 36379
Sommaire des Matières pour Cequent Towing Products 36379
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36379N 10-4-05 Rev. A 2005 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 1 de 3 36379N 10-4-05 Rev. A 2005 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 1 de 3 36379N 10-4-05 Rev. A 2005 Cequent Towing Products...