Distance To Combustible Material; Assembly; Releasing The Stove From The Pallet; Operating Control - Nordpeis Uno 1 Manuel D'installation

Warning: If the requirements for ventilation are
NOT complied with, the cooling airflow around the
product will be considerably reduced and
the product can overheat.
This can cause a fire.

3. Distance to combustible material

Ensure that the safety distances are respected
(FIG 1).
When connecting a steel chimney to the top outlet use
the security distances required from the manufacturer.

4. Assembly

The following tools are necessary:
•
5 mm Allen key (included)
•
10/17 mm wrench (included)
•
Screwdriver

Releasing the stove from the pallet:

Uno 1: Remove the screws holding the back cover
on the pedestal.Remove the back cover to acess det
screws holding the stove to the pallet. Remove the
screws using a 10mm wrench. Put the back cover back
in place and fasten the screw holding it.
Uno 2: The stove is fixed to the pallet both front and
rear. Use a 10mm wrench to remove the transport locks
fitted through the back plate of the product. To acess
the screws in front, the panel under the door must be
removed. Open the door and pull the lower panel
carefully outwards and up. Loosen the screws and push
the product forward to release it from the pallet.
Uno 4/5: Open the door under the combustion cham-
ber. Remove the fitting covering the leg adjustment and
the four screws holding the product to the pallet.

Operating control

When the stove is in an upright position, and prior
to connecting it, control that all functions are easy to
manoeuvre and appear satisfactory.
Door (FIG 2)
Handle is pulled out
Handle is pushed in
Air vent (FIG 2)
Forward
Backward
12
Open
Close
Closed
Open
Disassembling / Assembling Thermotte FIG 11-22
Dissasembling the Thermotte
FIG 12 - Uno 5;
FIG 13-16 - Uno 1, 2, 4 & 5.
FIG 12. Carefully pull the lower end of the side plate
silightly up and then pull towards the other side. The
same procedure utilize for second side plate.
FIG 13. Carefully pull the lower end of the back plate
diagonally towards the door. Leave it at an angle as
shown in the illustration.
FIG 14. Remove the smoke baffle by moving it carefully
to one side and clear of the rail on the other side. Place
the smoke baffle at an angle and carefully remove it
through the door.
FIG 15. Remove the back plate by tilting it carefully
through the door.
FIG 16. Lift the bottom plate up on one side and the the
other.
Assembling the Thermotte
FIG 17- FIG 21 - Uno 1, 2, 4, 5
FIG 22 - Uno 5.
FIG 17. Carefully tilt the bottom plate through the door
opening. Carefully lower it down on one side before
lowering it on the other.
FIG 18.Tilt the back plate through the door and place it
at an angle (bottom part towards the door) . Leave the
back plate at this angle FIG 19.
FIG 20. Carefully tilt the smoke baffle through the door
and place it eavenly above the upper rails, one side at
the time. Make sure the smoke baffle is centered FIG
20C.
FIG 21. When the smoke baffle is in place, carefully
push the bottom of the back plate in place.
FIG 22. Place carefully the side plate inside the com-
bustion chamber - set in diagonal position. Move the
plate pushing the lower end up and towards side. The
same procedure repeat with the second plate.

Adjustment of legs

Uno 1/2: Do not have adjustable legs
Uno 4/5
Open the door under the combustion chamber FIG 3.
Remove the fitting covering the leg adjustment and
adjust the legs with a 17 mm wrench.
In addition, Uno 4 has optional legs sold separately.
See manual Uno Legs for details.
GB