Preparations For Use; Operating - Roller's Fox ANC Instructions D'emploi

eng
1.5. Dimensions
ROLLER'S Fox ANC
ROLLER'S Fox ANC VE
ROLLER'S Fox ANC SR
ROLLER'S Mamba ANC VE
ROLLER'S Carat ANC VE
1.6. Weights
ROLLER'S Fox ANC
ROLLER'S Fox ANC VE
ROLLER'S Fox ANC SR
ROLLER'S Mamba ANC VE
ROLLER'S Carat ANC VE
ROLLER'S Guide support up to 2"
ROLLER'S Guide support 2
1.7. Noise data
Workplace-related emissions
all ROLLER'S reciprocating saws
Sound capacity level
ROLLER'S reciprocating saws
1.8. Vibrations
Weighted effective value of acceleration:
ROLLER'S Fox, all models with guide support
ROLLER'S Mamba ANC VE, ROLLER'S Carat ANC VE,
free-hand
All reciprocating saws idle

2. Preparations for Use

2.1. Electrical connection
Ensure correct mains voltage! Before connecting the drive unit res-
pectively the rapid charger, check whether voltage on the rating plate
matches the mains voltage. At work sites, in damp surroundings, in
the open or in case of comparable type of use, only operate the
equipment off the mains using a 30mA fault current protected switch
(FI breaker).
2.2. Sawing with guide support (square cutting)
Insert mounting pin (3) of the guide support (2) sideways into the saw
so that the stop pin of the guide support will move in the slot of the
machine.
Attention: To obtain square cuts, the use of the ROLLER'S guide
support is indispensable. Precise positioning is not possible when
saw is guided by hand.
2.3. Free hand sawing
The reciprocating saw is used without the guide support (2). It must
be pressed forcefully against the material during sawing, in a way that
the support shoe (6) touches the material at any time.
2.4. Choice of suitable blades
Only use the quality blades of ROLLER in combination with all
ROLLER'S reciprocating saws as otherwise any guarantee claim
becomes invalid!
For getting right angle cuts (e.g. pipes) with all ROLLER'S Fox
models it is essential not only to use the power transmitting guide
support (see 2.2.) but also the ROLLER'S special saw blade up to 2"
or 4". ROLLER'S special saw blades come with a double tang, are
extra thick and resistant to bending and distortion. Normal saw blades
with single tang do not withstand the high feed pressure during
sawing with the guide support. They cut skew and break at the
mounting point.
Furthermore, especially with ROLLER'S Mamba ANC VE and
ROLLER'S Carat ANC VE the ROLLER'S special saw blades
(561003 ... 561005) should be used. For special operations there are
other ROLLER'S saw blades available with different forms, lengths
and spacings. Please use the blade best suited by size, length and
tooth pitch. An unsuitable blade will easily break or become prema-
turely blunt and will result in inaccurate cuts. For sawing stainless
steel pipes and hard cast iron pipes use ROLLER'S Fox ANC SR and
one of the ROLLER'S special saw blades 561003 ... 561005.
While sawing excessive dust generating materials, e.g. blaster,
breeze blocks, for safety reasons and for protecting the gear against
wear, apply dust extractors.
455×80× 90 mm (17.9"×3.2"×3.5")
435×80×135 mm (17.1"×3.2"×5.3")
490×80× 90 mm (19.3"×3.2"×3.5")
320×80x110 mm (12.6"×3.2"×4.3")
435×80×135 mm (17.1"×3.2"×5.3")
3.0 kg (6.6 lb)
3.0 kg (6.6 lb)
3.1 kg (6.8 lb)
2.4 kg (5.3 lb)
3.0 kg (6.6 lb)
1.0 kg (2.2 lb)
1 / –4" 1.7 kg (3.7 lb)
2
2.5. Installing the saw blade
When installing the saw blade, take care not to place the saw on the
anti-kink sleeve on the mains lead, otherwise the lead may be
damaged. Loosen clamping screw (9) on saw blade thrust washer (4)
so that the blade can be inserted over the centering pin. The
ROLLER'S special saw blade must be positioned between the two
arms of the U-shaped thrust washer (Fig. 2). ROLLER saw blades
must be positioned in the recess in the base of the thrust washer
(Fig. 3). Secure the saw blade tightly with clamping screw (9), other-
wise the centering pin may become damaged or could shear. The
centering pin is not intended to hold the saw blade. This function is
performed by the clamping action of clamping screw (9). lf this cannot
be properly tightened, because the screw socket or socket wrench is
worn, the centering pin will shear off. For this reason, replace the
clamping screw (9) or socket wrench well before wear becomes
excessive.

3. Operating

98 dB(A)
ROLLER'S Fox ANC: On-/off with touch control (7).
104 dB(A)
ROLLER'S Fox ANC VE, ROLLER'S Mamba ANC VE and ROLLER'S
Carat ANC VE: Stepless speed control by pressing switch (10).
ROLLER'S Fox ANC SR: Speed adjustment with dial (12). On/off switching
with tip switch (7).
16.4 m/s 2
3.1. Operation while sawing with guide support
18 m/s 2 Mount guide support as described under 2.2. Position saw with guide
22 m/s 2 support onto the pipe so that the clamp spindle is vertical. Press tip
switch (7 or 10) while holding the motor handle at the same time,
respectively press lever (11), and pull up saw until pipe or rod is cut
through. Start-sawing, especially at large diameters (e.g. 4"), can be
improved by not switching the motor on before the saw blade touches
the pipe. Note that the prism of the guide support is to be kept clean
all the time, otherwise square cutting will be effected. For obtaining
optimum stroke speed and for protecting the saw blade, only apply
moderate feed forward. High force does not make sawing faster!
3.2. Operation while sawing free-hand
For straight or curved cutting, press support shoe (6) forcefully
against the material in a way that the support shoe (6) touches the
material at any time. Switch machine on. Use only sharp and faultless
blades. Take care to cut at a uniform feeding speed. This will reduce
the risk of accidents and wear on tool and blade. Always keep the
power cable towards the rear of the machine.
Plunge cutting into a plain surface: lf the material is not too hard e.g.
wood or plasterboards, the saw blade in motion can be plunged
carefully into the material (see Fig. 4). Before switching on machine
place tip of saw on the cutting point with machine resting on the lower
edge of support shoe. Switch on saw and plunge blade carefully into
material. For hard material such as metal first drill a starting hole
according to the size of the saw blade. lt is important to press the
support shoe (6) firmly against the material to be cut in order to obtain
a uniform and smooth cutting operation.
3.3. Lubricants
Do not use any lubricants. They will prevent the ejection of chips from
the cutting point and will reduce the life of the saw blades (see 3.4.).
3.4. Stainless steel pipes, hard cast iron pipes
For sawing stainless steel pipes and hard cast iron pipes use
ROLLER'S Fox ANC SR and one of the ROLLER'S universal saw
blades 561003 ... 561005. For square cutting the guide support is
essential (see 2.2.). Only when cutting stainless steel, use ROLLER'S
Smargdol or ROLLER Rubinol 2000 for cooling and lubricating.
4. Maintenance
Before any repair work, pull the mains plug or remove the battery!
4.1. Maintenance
The ROLLER'S reciprocating saws are maintenance free. The gear
runs in a sealed grease housing and therefore does not need any
lubrication.
4.2. Inspection/Servicing
Before any repair work, pull the mains plug or remove the battery!
This work may only be performed by authorised experts or by trained
personnel.
eng