In Case Of Difficulty; Specifications - Kenwood KA-S10 Mode D'emploi

In case of difficulty

What seems to be a malfunction is not always so. Before calling for service, check the following table ac-
cording to the symptom of your trouble.
Symptom
Sound is not produced.
No sound is output or noise interferes.
Sound is not produced from the left or right
speaker.
Sound volume is too low.
Sound is too loud and distorted.
Speaker protection circuit
The speaker protection circuit is activated when the unit is switched ON while the + and – speaker cords are shorted.
When activated, the speaker protection circuit shuts off the audio output to protect both the unit and speakers.
If the speaker cords are shorted, switch the unit OFF , unplug the power cord from the power outlet, and then reconnect
the speaker cords properly by removing the short-circuiting. Plug the power plug into the power outlet and set the
POWER switch to ON to reuse the unit.

Specifications

[Audio section]
Effective output power during STEREO operation
(1 kHz, 10 % T.H.D., at 8 Ω) ...... 12 W + 12 W (RMS)
(1 kHz, 10 % T.H.D., at 6 Ω) ...... 13 W + 13 W (RMS)
Rated output power during STEREO operation
(63 Hz ~ 12.5 kHz, at 8 Ω) ........... 10 W + 10 W (DIN)
(63 Hz ~ 12.5 kHz, at 6 Ω) ........... 11 W + 11 W (DIN)
Total harmonic distortion
............................. 0.03 % (AUX IN, 1 kHz, 6 W, 8 Ω)
N.B. Circuit
N.B. 1 ............................................. +3.0 dB (at 60 Hz)
N.B. 2 ............................................. +5.0 dB (at 70 Hz)
N.B. 3 ........................................... +7.5 dB (at 100 Hz)
Input (Sensitivity / Impedance)
LINE (CD, AUX) ............................... 250 mV / 22 kΩ
LINE (D.AUDIO) ............................... 140 mV / 48 kΩ
Output (Level / Impedance)
SUBWOOFER PREOUT ....................... 1.8 V / 2.9 kΩ
10
ENGLISH
÷ Connect properly referring to "Connections".
÷ Adjust to a required volume.
÷ Select the desired input source with the INPUT SELECTOR
knob.
÷ The speaker protection circuit may be activated. Read "Speaker
protection circuit" below and remove short-circuiting of the
speaker cords.
÷ Connect properly referring to "Connections".
÷ Connect properly referring to "Connections".
÷ If the headphones output of a portable component is connected
to the CD or AUX input connectors, reconnect it to the D.AUDIO
input connectors.
÷ Connect properly referring to "Connections".
÷ If the line output of a desktop component such as a CD player is
connected to the D.AUDIO input connectors, reconnect it to the
CD or AUX input connectors.
[General]
Power consumption .............................................. 28 W
Dimensions
Horizontal installation ............ W 171 mm (6-3/4 ")
Vertical installation ................. W 89 mm (3-1/2 ")
Weight (net) .................................................. 2 kg (4.4 lb)
Notes : KENWOOD follows a policy of continuous
advancements in development. For this reason specifica-
tions may be changed without notice.
÷ Sufficient performance may not be exhibited at ex-
tremely cold locations (where water freezes).
Remedy
H 67 mm (2-5/8 ")
D 207 mm (8-1/8 ")
H 182 mm(7-3/16 ")
D 207 mm (8-1/8 ")
67
9
9
0
67
67
6
67
6