Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
MAINTENANCE
The safety level given by the design of the Indoor Cycle can only be maintained when the equipment is regularly examined for
damage and wear. Inoperable components should be replaced or the equipment should be put out of use until it is repaired.
DAILY
• Wipe down the Indoor Cycle after each use to remove sweat and moisture. Use soap and water, or a diluted non-abrasive
domestic cleaner solution. Rinse to remove detergent residue and then dry off.
• Before each session, inspect for loose components such as pedals or cranks prior to commencing the next use. Tighten
up any loose parts.
WEEKLY
• Check for proper flywheel alignment. Torque flywheel nuts as necessary.
• Remove chain guard and check for loose chain. Adjust and lubricate the chain as necessary.
• Check to make sure the crank arms are tight to the bottom bracket.
• Inspect all parts, nuts, bolts, or screws for adjustments, replacements or maintenance.
MONTHLY
• Inspect the frame and main assembly components for rust or corrosion. Tilt the cycle or place in an upside down position
to locate areas where rust and corrosion may develop. Use a small, wire brush to remove rust build-up in small crevasses,
such as leveling feet, quick release levers and other bolt assemblies.
• Inspect all wear items for adjustments or possible part replacement. Give particular attention to the following:
A) Inspect brake pad for wear. Excessive wear or dryness indicates replacement is required.
B) Inspect seat pad for wear. Rips, tears or excessive movement indicates replacement is required.
C) Inspect pedals for play. Excessive movement of pedals indicates replacement is required.
• Inspect the chain for tensioning by rotating the crank to drive the flywheel forward. Do this motion in 1/4 turns to assess if
there is free play between the crank and the flywheel.
• Dryness or prolonged use may cause the height and reach adjustments for the seat and handlebar to become tight. If this
is the case, the sliding assembly should be removed from the frame and have a smear of light duty grease applied along
the sliding surface before assembly. Similarly, apply some light grease to the clamping assembly to ensure it does not seize
up. Clean off excessive grease before reassembly.
• Please lubricate the seat post, brake pad and handlebar adjustment regularly with lubricant in your parts package.
24
HZ18_GR7-GR7s OM r1_0_A.indd 24-25
GR7 EXPLODED VIEW
Q13X2
B
V08
R19
Q03
D07
B
Q08X2
AD1
Q05
C14
Q08X2
D07
L27X2
D05
Q04
AD2
T01
B28
Q08X4
Q01
B41
Q07X4
C
C
T03
R45
H07
C85
R37
R09
E
R35
R27X2
R12X2
R47X2
E
B66X2
V03
C83
F
V02
V01
R32X6
F
B42X4
F
B14
R06
R23X4
E
E
R21
R13X2
P25
R04
P23x2
P24X2
E
R05
R20X2
R14X2
R22X4
F08
F09
Z01X3
AJ2
F10X4
K50X2
B
B41
C
B30
B
L25X2
L24X2
B27
L18
C15
AG2
L05
L26X4
L17
B31
L29X2
G03
L25X3
B26
B32
C80
B
L20
B43
C06
AC1
F
L15
V07
L06
R40
L04
L21
B
L25X2
S01
L28X2
B
B29
B19
B37x2
C16
B19
E
B36x2
F
B18
B17
B33
F06
C11
Z01X2
V15
R31X4
Z02X2
R38
R32X2
R41
B34
D08
F07
B40X2
K13X2
B35X2
AJ1
R43
J05X2
AB1
F10X4
R39
K50X2
B
T12
R32
T09
T10
T11
AR2
R03
T13X5
Q06X2
Q09X2
Q14X3
R18
B
Q02
T02
B50X2
Q11X4
E
B51X2
T05X4
T16
T06X2
R10
T04
R11
R24
R08
R07
R26
V04
V02
C
V06
T03
V20X4
D
C
C
E
B
25
6/27/18 11:30 AM
Publicité
Table des Matières
