Important Instructions Regarding Safety And Environment; Transportation Safety; Installation Safety - Beko GN1416230CXPN Manuel D'utilisation

Réfrigérateur
Masquer les pouces Voir aussi pour GN1416230CXPN:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 36

Important instructions regarding safety and environment

the manufacturer, authorised service agent or
importer in order to avoid potential dangers.
Do not squeeze the power cable under or behind
the product. Do not place heavy objects on the
power cable. Power cable must not be bent
excessively, pinched or get in contact with any
heat source.
Do not use extension cords, multi-sockets or
adapters to operate the product.
Portable multi-sockets or portable power sources
can overheat and cause fire. Therefore, do
not keep any multi-sockets behind or near the
product.
Plug must be easily accessible. If this is not
possible, the electrical installation to which the
product is connected must contain a device
(such as a fuse, switch, circuit breaker, etc.)
which conforms to the electrical regulations and
disconnects all poles from the grid.
Do not touch the power plug with wet hands.
Remove the plug from the socket by gripping the
plug and not the cable.

1.4 - Transportation safety

Product is heavy; do not move it alone.
Do not hold its door when moving the product.
Pay attention not to damage the cooling system
or the piping during transportation. If the piping is
damaged, do not operate the product and call the
authorised service agent.

1.5 - Installation safety

Call the authorised service agent for installation of
the product. To make the product ready for use,
check the information in the user manual to make
sure that the electricity and water installations are
suitable. If they are not, call a qualified electrician
and plumber to have the necessary arrangements
made. Otherwise, there is the risk of electric
shock, fire, problems with the product, or injury!
Prior to installation, check if the product has any
defects on it. If the product is damaged, do not
have it installed.
Place the product on a clean, flat and solid
surface and balance it with adjustable feet.
Otherwise, the product may tip over and cause
injuries.
The installation location must be dry and well
ventilated. Do not place carpets, rugs or similar
covers under the product. Insufficient ventilation
causes the risk of fire!
Do not cover or block the ventilation openings.
Otherwise, power consumption increases and
your product may get damaged.
Product must not be connected to supply
systems such as solar power supplies.
Otherwise, your product may get damaged due
to sudden voltage changes!
The more refrigerant a refrigerator contains,
the larger the installation location must be. If
the installation location is too small, flammable
refrigerant and air mixture will accumulate in
cases of refrigerant leakage in cooling system.
The required space for each 8 gr of refrigerant
is 1 m³ minimum. The amount of refrigerant in
your product is indicated on the Type Label.
Product must not be installed in places exposed
to direct sunlight and it must be kept away from
heat sources such as hobs, radiators, etc.
If it is inevitable to install the product close to
a heat source, a suitable insulation plate must
be used in between and the following minimum
distances must be kept to the heat source:
- Minimum 30 cm away from heat sources
such as hobs, ovens, heater units or stoves,
- Minimum 5 cm away from electric ovens.
Protection class of your product is Type I.
Plug the product in a grounded socket that
conforms the voltage, current and frequency
values stated on the type label of the product.
The socket must be equipped with a 10 A – 16
A circuit breaker. Our company shall not be
liable for any damages that will arise when
the product is used without grounding and
electrical connection in accordance with the
local and national regulations.
Product must not be plugged in during
installation. Otherwise, there is the risk of
electric shock and injury!
Do not plug the product in sockets that are
loose, dislocated, broken, dirty, greasy or bear
the risk of getting in contact with water.
Route the power cable and hoses (if any) of the
product in a way that they do not cause risk of
tripping over.
3 /30 EN
Refrigerator / User Manual

Publicité

Table des Matières
loading

Table des Matières