Legal Warnings; Guarantee Provisions - Niko 170-40000 Mode D'emploi

Module (24V) with 4 or 6 potential free push buttons
Read the complete manual before attempting installation and activating the system.
1. DESCRIPTION
- The module (24V) with 4 or 6 potential free push buttons serves to control remote switches (teleruptors) and home automation systems.
For controlling a Nikobus home automation system, the interface for push buttons (05-056 or 05-058) can be used!
For other wiring diagrams concerning the Nikobus system, see technical part of the catalogue or our website.
- Wiring diagrams: see enclosure
Technical specifications:
If you work with a remote switch, connect the push button module to 24V~ via a short circuit proof safety transformer.
If the feedback LEDs of your home automation system do not operate at 24V, you have to provide an adaptation to 24V DC yourself.
use of 24V for module
remote switch 24V~ via short circuit proof
(AC current)
other systems
(DC current)
- Controlling dimmers: only connect dimmers that are galvanically isolated: 05-707 / 05-715 / 65-410 / 65-412 / 65-416.
Every module is available in 4 different versions: 2 different types of bridges, both available with and without claws. The availability of these versions depends on the accepted installation method in your country.
4-fold potential free push button without LED
with claws for screwing
}
170-40000 170-40001
170-70000 170-70000
05321 05321 05321 05321
170-47000 170-47001
* for the text field, you can use:
- the supplied label
- a Dymo-label of 12mm
- a label you can design yourself via www.niko.be/labels
6-fold potential free push button without LED
with claws for screwing
}
170-60000 170-60001
170-70000 170-70000
05321 05321 05321 05321
170-67000 170-67001

2. LEGAL WARNINGS

- The installation has to be carried out by a registered installer and in compliance with the statutory regulations.
- This user manual has to be handed over to the user. It has to be included in the electrical installation file and has to be passed on to any new owners. Additional copies are available on the Niko website or via the support service.
- During installation, the following has to be taken into account (not limited to list below):
- The statutory laws, standards and regulations;
- The state of the art technique at the moment of installation;
- This user manual, which must be read within the scope of each specific installation, only states general regulations;
- The rules of proper workmanship
- In case of questions, you can consult Niko's support service or contact a registered control organisation.
Support Belgium: Support UK:
+32 3 778 90 80 +44 1525877707
website : http://www.niko.be http://www.nikouk.com
e-mail: support@niko.be sales@nikouk.com
In case of a defect, you can return your product to a registered Niko wholesaler, together with a clear description of your complaint (Conditions of use, stated defect...).

3. GUARANTEE PROVISIONS

- Period of guarantee: 2 years from date of delivery. The delivery date is the invoice date of purchase of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the defect, within two months after stating the defect.
- In case of a failure to conform, the consumer has the right to a repair or replacement (decided by Niko) free of charge.
- Niko cannot be held liable for a defect or damage as a result of an incorrect installation, improper or careless use or wrong usage or transformation of the goods.
- The compulsory regulations of the national legislation concerning the sales of consumer goods and the protection of the consumers in the countries where Niko sells, directly or via sister or daughter companies, chain stores,
distributors, agents or permanent sales representatives, take priority over the rules and regulations mentioned above.
nv Niko sa
switching capacity push button
max. 25VA
safety transformer
0 - 24V DC
possible finishings wiring diagram
B
C 1 A B
C D E F
XXX-40000
or
C
C 2 1 2
*
3 4 5
XXX-40200
C1 A B C D
finishing wiring diagram
B
C 1 A B
C D E F
F
C
XXX-60001
C 2 1 2
3 4 5
C1 A B C D E
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@Niko.be — www.niko.be
max. power supply LED (24V, ±10%)
push button
4 LEDs = 9mA
6 LEDs = 13mA
4 LEDs = 5mA
1A
6 LEDs = 7,5mA
with claws
A
170-401Y0
170-70000
6
D
05321 05321
170-471Y0
Y = 0 —> LED amber
Y = 1 —> LED blue
with claws
A
170-601Y0
E
170-70000
D
6
05321 05321
F
170-671Y0
Y = 0 —> LED amber
Y = 1 —> LED blue
signaling cable
8/10/12/14/16/20
min. 0,5mm - max. 0,8mm
4-fold potential free push button with LED
for screwing possible finishings
2B
}
XXX-40100
170-401Y1
or
170-70000
3C
*
XXX-40300
05321 05321
C1
170-471Y1
C2
6-fold potential free push button with LED
for screwing finishing
2B
}
6F
170-601Y1
170-70000
3C
XXX-60100
05321 05321
C1
170-671Y1
C2
for LEDs
terminal C2 = +
terminals 123456 = -
wiring diagram
C 1 A B
A1
C D E F
C 2 1 2
3 4 5
D4
6
A B C D
1 2 3 4
wiring diagram
C 1 A B
A1
C D E F
E5
C 2 1 2
3 4 5
D4
6
A B C D E F
1 2 3 4 5 6
PM170-40000R08432