Functional Description - Milwaukee 6310-20 Manuel De L'utilisateur

Masquer les pouces Voir aussi pour 6310-20:

Manuel de l'utilisateur (24 pages)

Manuel de l'utilisateur (32 pages)

Manuel de l'utilisateur (33 pages)

Table Des Matières

Table des Matières

Les langues disponibles

c. When restarting a saw in the workpiece, cen-

ter the saw blade in the kerf and check that

saw teeth are not engaged into the material. If

saw blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

d. Support large panels to minimize the risk of

blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both sides,

near the line of cut and near the edge of the

panel.

e. Do not use dull or damaged blade. Unsharp-

ened or improperly set blades produce narrow

kerf causing excessive friction, blade binding and

kickback.

f. Blade depth and bevel adjusting locking le-

vers must be tight and secure before making

cut. If blade adjustment shifts while cutting, it may

cause binding and kickback.

g. Use extra caution when making a "Plunge

Cut" into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

10.Check lower guard for proper closing before

each use. Do not operate the saw if lower

guard does not move freely and close in-

stantly. Never clamp or tie the lower guard into

the open position. If saw is accidentally dropped,

lower guard may be bent. Raise the lower guard

with the retracting handle and make sure it moves

freely and does not touch the blade or any other

part, in all angles and depths of cut.

11. Check the operation and condition of the

lower guard spring. If the guard and the

spring are not operating properly, they must

be serviced before use. Lower guard may op-

erate sluggishly due to damaged parts, gummy

deposits, or a buildup of debris.

Speciﬁ cations

Volts

No Load

Cat.

No.

RPM

6310-20

3200

12.Lower guard should be retracted manually

only for special cuts such as "Plunge Cuts"

and "Compound Cuts". Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must be

released. For all other sawing, the lower guard

should operate automatically.

13. Always observe that the lower guard is

overing the blade before placing saw down

on bench or ﬂ oor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is

released.

14.Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

15.WARNING: Some dust created by power sand-

ing, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

speciﬁ cally designed to ﬁ lter out microscopic

particles.

Blade

Depth of Cut

Arbor

Size

At 90°

6-1/2"

5/8"

0 to 2-1/8"

0 to 1-9/16"

Symbology

Direct Current

No Load Revolutions per

Minute (RPM)

Underwriters Laboratories, Inc.

United States and Canada

Lock-off button

Trigger

Handle

Shoe

Lower guard lever

Lower guard

Blade bolt

at 45°