U.S.Robotics USR7901A Guide D'installation

Cardbus 10/100 Ethernet PC Card
Installation Guide
USR7901A
Package Contents:
Cardbus 10/
Installation
100 Ethernet Quick Installation
CD-ROM
PC Card Guide (this guide)
Note: For the most updated information, visit: http://www.usr.com/support
U.S. Robotics Cardbus 10/100 Ethernet PC Card
Installation
Before you begin
Before you begin, we recommend you uninstall any other Network Interface Cards (NICs) you
have in your system Refer to your old NIC's documentation for removal instructions.
Write the serial number of the U.S. Robotics Cardbus 10/100 Mbps PC Card in the space below.
The serial number is located on the NIC and on the NIC's box.
NOT T T T T E: E: E: E: E: NO NO NO NO It is very important that you have your serial number written down for future reference. If
you ever need to call our Technical Support department, you will need this number to receive
assistance
NO NOT T T T T E: E: E: E: E: NO NO NO Touch an unpainted metal area of your computer's case to ground yourself. This will
protect your equipment from electrostatic discharge.
Installation Procedur Installation P Installation P
Installation P Installation P
All Users: All Users: All Users: All Users: All Users:
With your laptop computer turned on, locate an available PCMCIA slot. Insert the U.S. Robotics
Cardbus 10/100 Ethernet PC Card completely into the PCMCIA slot.
Windows 98 Users:
When Windows detects the new hardware, click Next. Select Search for the best driver for
your device and click Next.
Insert the Installation CD-ROM into your CD-ROM drive. Select Specify a location, type D:\, and
click Next. (If your CD-ROM drive uses a different letter, type that letter in place of "D".) When
Windows locates the driver, click Next.
After the driver installation is complete, remove the Installation CD-ROM from your CD-ROM
drive, click Finish, and then click Yes to restart your computer. When the computer restarts,
the installation procedure will be complete.
Windows 2000 Users:
When the Found New Hardware Wizard detects the Ethernet Controller, click Next. Select
Search for a suitable driver for my device (recommended) and click Next.
part number: R24.0465.00
Printed in Taiwan
Insert the Installation CD-ROM into your CD-ROM drive. Make sure that only Specify a location
is selected and click Next. Type D:\ and click OK. (If your CD-ROM drive uses a different letter,
type that letter in place of "D".) When the correct drivers are found, click Next. If you receive
a "Digital Signature Not Found Screen, click Yes to continue the installation.*
After the driver installation is complete, remove the Installation CD-ROM from your CD-ROM
drive, and click Finish. You may be then prompted to restart your computer. If you are, click
Yes and your computer will restart to complete the installation procedure.
*You may receive a "Digital Signature Not Found" screen. Click Yes. U.S. Robotics has thoroughly tested
Troubleshooting
this driver in conjunction with the supported hardware and has verified compatibility with Windows 2000,
Guide
Me, and XP. Because U.S. Robotics wants its customers to take full advantage of the network card's
functionality, it has made the drivers available.
Windows Me Users:
When Windows detects the new hardware, click Next. Select Specify the location of the driver
and click Next.
Insert the Installation CD into your CD-ROM drive. Select Specify a location, type D:\ and click
Next. (If your CD-ROM drive uses a different letter, type that letter in place of "D".) Follow the
on-screen instructions. When the correct driver is located, click Next.*
After the driver installation is complete, remove the Installation CD from your CD-ROM drive,
click Finish, and then click Yes to restart your computer. When the computer restarts, the
installation procedure will be complete.
*You may receive a "Digital Signature Not Found" screen. Click Continue Anyway. U.S. Robotics has
thoroughly tested this driver in conjunction with the supported hardware and has verified compatibility
with Windows 2000, Me, and XP. Because U.S. Robotics wants its customers to take full advantage of the
network card's functionality, it has made the drivers available.
Windows NT Users:
Click Windows Start, Settings, and then Control Panel. Double-click Network and click the
Adapters tab. Click the Add button and then click the Have Disk button.
Insert the Installation CD-ROM into your CD-ROM drive. Type D:\ and click OK. (If your CD-ROM
drive uses a different letter, type that letter in place of "D".) Select the U.S. Robotics Cardbus
10/100 Ethernet PC Card and click OK. Follow the on-screen instructions.
When you return to the Network window, click Close. Remove the Installation CD-ROM from
rocedur rocedure e e e e rocedur
rocedur
your CD-ROM drive. You will then be prompted for the TCP/IP properties. Select the U.S. Robotics
Cardbus 10/100 Ethernet PC Card from the adapter pulldown menu.
Assuming you are connected to a network, if you know your IP settings, select Use the following IP
address and enter the information in the appropriate fields. If you do not know your IP settings,
select Obtain an IP address from a DHCP server and click OK.
Follow the on-screen instructions and then click Yes to restart your computer.
Windows XP Users:
When the Found New Hardware Wizard detects the NIC, select Install from a list or specific
location (Advanced) and click Next. Insert the Installation CD-ROM into your CD-ROM drive.
Select Install the software automatically. Click Continue Anyway on the Harware Installation
screen.*
After the driver installation is complete, click Finish to complete the installation procedure.
*You may receive a "Digital Signature Not Found" screen. Click Continue Anyway. U.S. Robotics has
thoroughly tested this driver in conjunction with the supported hardware and has verified compatibility
with Windows 2000, Me, and XP. Because U.S. Robotics wants its customers to take full advantage of the
network card's functionality, it has made the drivers available.
Windows 95, LINUX, and DOS Users:
The CD-ROM includes the drivers for your operating system. On the Installation CD-ROM, you
can locate the folder containing the driver that applies to your operating system.
Congratulations!
You have finished installing the U.S. Robotics Cardbus 10/100
Ethernet PC card .
For troubleshooting and technical support information, refer to the Troubleshooting Guide.
Install the Communications Software
At the U.S. Robotics Installation CD-ROM interface, click the Software link. Listed here are
optional software applications that you can install for use with your U.S. Robotics Cardbus 10/100
Ethernet PC Card.
Register your product
At the U.S. Robotics Installation CD-ROM interface, click the Support link. Click Registration and
Warranty and then click http://www.usr.com/productreg
You can also launch a Web browser and type in the above web address.