Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51159F
Wrenches: 10mm, 14mm, 17mm, 19mm
Drill Bits: None
Frame Rail
jk
Fits with mini spare tire stowed under vehicle. Will not fit with full size spare.
j
Qty. (6)
Hex Bolt M12 x 1.25 x 35mm CL8.8
Note: Transmission cooler and Power Steering cooler are required for max. towing capacity (See vehicle owner's manual for details).
2001-2003 Acura MDX & 2001 and later Honda Pilot:
Remove tow hook from driver's side of vehicle and return hook and fasteners to vehicle owner.
1.
2.
Lower exhaust by removing three rubber muffler hangers.
3.
Raise hitch into position and install fasteners as shown above.
4.
Reinstall muffler hangers removed in step 2.
5.
If exhaust rattle occurs, trim rearward exhaust heat shield between crosstube and muffler.
2004 Acura MDX
Remove tow hook from driver's side of vehicle and return hook and fasteners to vehicle owner.
1.
2.
Remove fascia under covering by removing bolts and fascia clips shown above and return to vehicle owner.
3.
Lower exhaust by removing four rubber muffler hangers.
4.
Raise hitch into position and install fasteners as shown above.
5.
Reinstall muffler hangers removed in step 3.
Tighten all m12 x 1.25 CL8.8 fasteners with torque wrench to 68 Lb.-Ft.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
©
2009, 2012, 2013 Cequent Performance Products – Printed in Mexico
Installation Instructions
Bumper
Acura MDX
Honda Pilot
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3
Fascia under covering
(some models)
Fasteners Typical Both
Sides of Vehicle
k
Conical Washer – ½"
Qty. (6)
Sheet 1 of 3
51159N
Part Numbers:
51159
97159
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5000 (2270 Kg)
500 (227 Kg)
3500 (1589 Kg)
350 (159 Kg)
Existing weldnuts
(both sides)
10-24-13
Form: F205 Rev A 5-6-05
Rev. C
Publicité
Manuels Connexes pour Cequent Performance Products 51159
Sommaire des Matières pour Cequent Performance Products 51159
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2009, 2012, 2013 Cequent Performance Products – Printed in Mexico Sheet 1 of 3 51159N 10-24-13 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2009, 2012, 2013 Cequent Performance Products – Imprimé au Mexique Feuille 2 de 3 51159N 10-24-13 Rev.
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2009, 2012, 2013 Cequent Performance Products – Impreso en México Sheet 3 of 3 51159N 10-24-13 Rev.