Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Bumper
Structure
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51149F
Wrenches: 3/4"
1
Qty. (4)
Hex Bolt, 1/2-13 x 4"
2
Qty. (4)
Conical Washer, 1/2"
For vehicles with OEM Tow Hook: Tow hook must be permanently removed for hitch
installation. Installation time will increase from 20 Min. to 90 Min.
1.
Lower the spare tire.
2.
Remove two plastic pins that hold bumper fascia onto bumper structure as shown in Figure 1. (If OEM tow hook is present: Remove fascia,
plastic bumper support and tow hook)
3.
Gently pull fascia rearward about one inch and raise the hitch into position as shown in Figure 1.
4.
If there is excessive gap between the vertical surfaces of the hitch and the bumper structures, flat washers should be used as shims. They can
be held in place using cellophane tape. See Figure 2.
5.
Secure hitch with fasteners. Fascia may contact the back of the hitch. (Reinstall fascia and plastic bumper support if removed in Step 2.)
6.
Replace plastic pins in bumper fascia.
7.
Raise the spare tire into storage position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Bumper
Fascia
Jeep Grand Cherokee
Jeep Commander
Bumper
Structure
FIGURE 1
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Fascia
Pins
3
Qty. (8)
Flat Washer, 1/2"
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
7500 (3405 Kg)
5000 (2270 Kg)
FIGURE 2
51149N
8-11-09
51149
Max Tongue
WT (LB)
750 (341 Kg)
500 (227 Kg)
Rev. A
Publicité
Manuels Connexes pour Cequent Performance Products 51149
Sommaire des Matières pour Cequent Performance Products 51149
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51149N 8-11-09 Rev. A 2009 Cequent Performance Products...
- Page 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51149N 8-11-09 Rev. A 2009 Cequent Performance Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 51149N 8-11-09 Rev. A 2009 Cequent Performance Products...