Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Carbon Canister
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51174F
Wrenches: 12mm, 14mm, 17mm
Drill Bits: None
Tie-down Bracket
Exhaust Mounting Bracket
1
Qty. (7)
M12 X 1.25 X 40mm Hex Bolt
2
Qty. (7)
1/2 Conical Washer
3
Qty. (1)
M10 X 1.50 Hex Bolt
4
Qty. (2)
7/16 Flat Washer
1.
Lower carbon canister and bracket from passenger side of frame.
2.
Remove the tie-down bracket from vehicle frame.
3.
Remove center fascia mounting bracket if present.
4.
Remove exhaust mounting bracket from vehicle frame. (Return tie-down brackets, exhaust mounting bracket, center fascia
bracket & fasteners to vehicle owner for reinstallation if hitch is removed).
5.
Bolt hitch to vehicle. Sandwiching carbon canister bracket between hitch and frame. Using fasteners provided as shown
above.
6.
Bolt rubber exhaust hanger to hitch side bracket using fasteners provided as shown above.
7.
Reattach carbon canister to carbon canister bracket.
8.
Reattach center fascia tab if present to hitch with existing fastener or cable tie provided.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
SUBARU FORESTER
Plastic Bumper Fascia
Drawbar Kit:
36051
Drawbar must be used in the
RISE position only.
Carbon Canister Bracket
Frame
5
6
7
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Tighten all M10 fasteners with torque wrench to 20-30 Lb.-Ft. (27-41 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 KG) Max Gross Trailer Weight
300 LB (136 KG) Max Tongue Weight
Wiring Access Location: SUV4
Attach Center Fascia Tab Here
Using Cable Tie Provided
Qty. (1)
7/16 Lock Washer
Qty. (1)
M10 X 1.25 Hex Nut
Qty. (1)
Cable Tie
51174N
Part Numbers:
51174
Existing Weld nut
Tie-down
Bracket
8-26-09
Rev. A
Publicité
Manuels Connexes pour Cequent Performance Products 51174
Sommaire des Matières pour Cequent Performance Products 51174
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51174N 8-26-09 Rev. A 2009 Cequent Performance Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51174N 8-26-09 Rev. A 2009 Cequent Performance Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 51174N 8-26-09 Rev. A 2009 Cequent Performance Products...