Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Fitting Straps into End Supports
Prior to Assembly, check that your Roof Rack Box contains all the parts
as shown above. Ensure that the vehicle roof is clean and dry.
Please note that some illustrations depicted in these instructions are
only representative and your items may look different.
Read these instructions carefully before commencing.
You can use a protective cloth when installing your racks to protect
of vehicle's finish.
Ensure your straps correspond with the mounting positions on
the vehicle before installing them into the End Supports. Use
strap position labels to identify the correct car position.
1. Un-fasten and rotate the Covers off the End Supports. The
Covers can remain attached to the Hinge on the Supports.
2. Remove the Gasket Pads by carefully pulling them off the
End Supports (Pads are clipped on by "T" clips).
3. Feed the Strap neck through the cavity in the End Support (Fig 1a).
When the Neck is through rotate the Strap down and then push up to
align the bolt hole and the cage nut.
4.Use the supplied "L" wrench to feed the bolts into the cage
nuts (Fig 1b). The "L" wrench is located inside the support.
5. Leave approximately 1" (25mm) of gap between the top of
the Strap and the bolt head . This will aid in installation to the
door frame (Fig 1c)
Placement of End Supports onto Vehicle Roof
6. The Gasket Pads all have vehicle roof
position text on the top inside surface.
Left (Drivers side), Right (Passenger side)
These can now be replaced on the end
supports. Re-fasten using the T clips
7. Using the vehicles B pillar place the
cross bars as specified in ( Fig 2 a & b)
Note: Gasket only shown for clarity.
59709N
7/20/11
Mazda 6
2009 and Up
Roof Rack Installation Guide
Gasket Pads are pre-
attached to the Supports
Fig 1a
Front
Fig 2a
PART No.
Carrying Capacity
2
1
25mm
(1")
Fig 1c
700mm (27-1/2" )
Note- You may place the cross bar
position labels in the door frame
below the Straps for future reference.
59709
50 kgs
110 lbs
Note: Keys may be
packaged separately
in the kit
TIP: Pull the Buffer Strips back
approximately 1-1/2" (40mm)
to allow good access for the "L"
wrench to fit into the bolt
head.
Fig 1b
Fig 2b
315mm
(12-1/2")
Front
Page 1 of 2
Publicité
Manuels Connexes pour Rola 59709
Sommaire des Matières pour Rola 59709
- Page 1 59709 PART No. Mazda 6 2009 and Up 50 kgs Roof Rack Installation Guide Carrying Capacity 110 lbs Note: Keys may be packaged separately in the kit Gasket Pads are pre- attached to the Supports Fitting Straps into End Supports Prior to Assembly, check that your Roof Rack Box contains all the parts as shown above.
- Page 2 Installation Instructions: Mazda 6 2009 and Up 8. With one strap loosely mated around the door frame, Fig 2c Fig 2d hold the other side Strap out from the body side and place PUSH into the door frame. (Fig 2c) PULL Ensure the rubber pads on the straps are in place to avoid paint damage.
- Page 3 59709 No PIÈCE Mazda 6 sans barres de toit 2009 et plus récent 50 kg Guide d'installation du porte-bagages de toit Capacité de charge 110 lb Remarque : Dans l'ensemble, les clés peuvent se trouver dans un emballage séparé Les coussinets de joints sont pré-attachés aux supports...
- Page 4 Instructions d'installation : Mazda 6 2009 et plus récent 8. Avec une sangle attachée autour du cadre de porte d'une Fig. 2c Fig. 2d manière lâche, tenir la sangle de l'autre côté à l'extérieur de la paroi de la carosserie, puis la placer dans le cadre de POUSSER TIRER portière.