Makita DMR050 Manuel D'instructions page 5

NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Operating the radio
WARNING:
Avoid using this unit in metal dust surrounding, as it will
affect the quality of the speaker.
WARNING:
Do not soak the unit into water. It can only tolerate in the
environment under 90% of humidity.
This unit equips with three tuning methods- Scan tuning,
Manual tuning and Memory presets recall.
Scan tuning
1. Press the Radio power button [
radio.
2. Select the desired waveband (i.e. AM/FM) by brief
pressing the Power button [
Note:
Make sure the antenna has been extended for the best
FM reception. For AM band, rotate the radio horizontally
to get the best signal.
Important:
Try to avoid operating the radio next to computer screen
and other equipment which will cause interference to the
radio.
3. Press and hold the Radio Station Tuning Up/Down
button [ ] over 0.5 seconds. The frequency will
stop at the next available station.
4. Press the Volume Up/Down button [
optimal sound level. LCD display will show sound level
changes (0-40 steps).
5. To turn off the radio, press and hold the Power button
[ ] until OFF is shown on the LCD display.
Manual tuning
1. Press the Radio power button [
radio.
2. Select the desired waveband (i.e. AM/FM) by brief
pressing the Power button [
Note:
Make sure the antenna has been extended for the best
FM reception. For AM (MW) band, rotate the radio to get
the best signal.
3. Press the Tuning Up/Down Control [
desired frequency shown on the display.
4. Press the Volume Up/Down button [
optimal sound level.
5. To turn off the radio, press and hold the Radio power
button [ ] until OFF is shown on the LCD display.
Storing stations in presets memories
There are 3 memory presets for each waveband.
1. Press the Radio power button [
radio.
2. Tune to desired station using the steps previously
described.
] to turn on the
].
] to get the
] to turn on the
].
] until the
] to get the
] to turn on the
3. Press and hold the desired Preset button (approx.
3 sec) until the preset number stop flashing on the
display. The preset number will appear in the display
and the station will be stored under chosen preset
button.
4. Repeat this procedure for the remaining presets.
Note:
Stations stored in preset memories can be overwritten by
following above procedures.
Recall stations from preset memories
1. Press the Radio power button [
radio.
2. Select the desired waveband.
3. Press the desired Preset button, the preset number
and station frequency will appear in the display.
System reset
If your radio fails to work properly, or some digits on the
display are missing or incomplete, carry out the following
procedure.
Note:
To reset the system, you must put the radio in OFF
mode.
1. Press the Radio power button [
radio.
2. Press and hold both the preset button 3 [
Radio power button [
5 seconds. When the LCD shows a display of all the
icons, all the preset memories are back to factory
default.
Using flash light (Fig. 8)
WARNING:
To reduce the risk of injury, do not look directly into the
light when the work light is on.
WARNING:
To reduce the risk of injury, DO NOT operate work light
without bezel assembly in place.
Using and adjusting the pivot head
Press the flash light button [
flashlight when the radio is either on or off.
Note:
The pivot head can pivot to a range of 150 degrees and
can be adjusted in 6 stages. Pivot head to desired
position. Allow the detent to snap into place.
Important:
Do not forcibly pivot the head.
LCD back light
Press any control buttons, LCD display will illuminate for
approx. 10 seconds.
] to turn on the
] to turn off the
] and the
] for approximately
] to switch on/off the
5