Panasonic MC-CG381 Instructions D'utilisation page 5

C - HOW TO OPERATE YOUR CLEANER
C-1 Pull out the power cord and put the plug into the
socket outlet.
C-2 Power control
: OFF
You can turn the appliance ON by turning it to the
clockwise direction.
MIN:Lowest suction.
MAX:Highest suction.
C-3 Switching between carpet and fl ooring
Flooring: Press lever A
Carpet: Press lever B
C-4 After you fi nish vacuuming, remove the plug from
the socket outlet and press the cord rewind pedal.
When rewinding the power cord, press the
cord rewind pedal holding the plug so that it does not
become damaged.
C-5 Storage position
Slide the wand holder straight into the wand
supporter.
C-6 Park position
For short breaks during vacuuming, slide the wand
holder into slot on the rear side of main body.
NOTE: When you use park position, we suggest that
you switch the appliance off.
D - MAINTENANCE AND SERVICING
CAUTIONS
• The plug must be removed from the socket outlet
before cleaning or maintaining the appliance.
• DO NOT use hot air or hot surface to dry fi lters. Dry
them at room temperature for approximately 24 hours.
• IMPORTANT: Before re-installing the washable fi lters,
make sure they are completely dry to avoid damaging
the appliance.
NOTE: If the paper dust bag is not properly installed, the dust
cover will not close. Be sure to check that the paper
dust bag is properly installed before operating the
appliance, otherwise dust will leak out.
The dust bag can easily lay on the dust cover
packing or clip between the bag collar and the body,
so be sure to properly extend it into the body of the
appliance.
Replacing the paper dust bag
D-1 Lift the dust cover catch and raise the dust cover until
it clicks properly.
D-2 Remove the bag collar from the bag holder and pull
out the paper dust bag.
D-3 Put in a new paper dust bag.
D-4 Close the dust cover properly until you hear it click.
Floor nozzle
D-5 Inspect once a month.
Using an old toothbrush or similar tool, clean any dirt
or lint from the brush.
Vacuum cleaner body
D-6 Wipe with a soft cloth soaked with water.
Maintaining the Pre-motor Filter
Follow the procedure written below when the suction power
is not restored after replacing a new paper dust bag.
D-7 Open the dust cover.
D-8 Remove the pre-motor fi lter.
D-9 Wash gently with water and then allow to dry in a
shaded location.
D-10 Return the pre-motor fi lter to its original position.
NOTE: Make sure you remember to replace the fi lter.
If the fi lter is not installed, it will cause motor
failure.
• Do not wash the fi lter in a washing machine or dry it
with a dryer or other source of hot air.
What to do if your cleaner does not work
Check that the appliance is correctly plugged in and that the
socket outlet is working. If the thermal cut-out device has
operated, wait until it resets automatically after approximately 60
minutes.
If after having checked the above mentioned points, the
appliance does not work, take it to an Authorized Service Centre
to be repaired.
What to do when the suction performance
reduces
• Stop the appliance and unplug from the socket outlet.
• Check whether the wands, hose and accessories are blocked or
not. If they are blocked, remove the obstruction.
• Check whether the paper dust bag is full. If it is full, replace it.
• Check whether the pre-motor fi lter is blocked with dust.
If they are blocked, clean them out or replace them.
SPECIFICATIONS
Power source
Current
Dimensions (W x L x H)
Net weight
Extension wands
Multipurpose accessory
Optional Accessory
Product name
Paper dust bag (PACK 5/u.)
REMINDER FOR CUSTOMER
The model and serial number of this product may be found on
the nameplate located on the underside of your appliance. You
should note the model and serial number in the spaces provided
and retain this book as a permanent record of your purchase.
Model Number. .............................................................................
Serial No. ......................................................................................
Date Purchased. ...........................................................................
Where Purchased. ........................................................................
5
MC-CG381
120 V~60 Hz
10 Amps
240 mm x 350 mm x 250 mm
3.8 kg
Metal x 2
√
Model number
C-20E