Controlling A Tv With The Remote; Troubleshooting - Samsung DVD-HD841 Mode D'emploi

Controlling a TV with the Remote

The remote can also be set up to control most TVs. To program the remote, use the
code that corresponds to your brand.
BRAND CODE
ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18
AIWA 82
BANG&OLUFSEN 57
BLAUPUNKT 71
BRANDT 73
BRIONVEGA 57
CGE 52
CONTINENTAL EDISON 75
19, 20, 23, 24, 25, 26, 27, 28, 29,
DAEWOO
30 , 31, 32, 33, 34
EMERSON 64
FERGUSON 73
FINLUX 06, 49, 57
FORMENTI 57
FUJITSU 84
GRADIENTE 70
GRUNDIG 49, 52, 71
HITACHI 60, 72, 73, 75
IMPERIAL 52
JVC 61, 79
LG 06, 19, 20, 21, 22, 78
LOEWE 06, 69
LOEWE OPTA 06, 57
MAGNAVOX 40
METZ 57
MITSUBISHI 06, 48, 62, 65
MIVAR 52, 77
NEC 83
NEWSAN 68
NOBLEX 66
1. Turn on the TV.
2. Point the DVD's remote at the TV.
3. While holding the TV POWER button down, enter
the code for your brand.
e.g) For Samsung 2 TVs
While holding down the TV POWER button,
enter 0 and then 1.
TV Codes
BRAND CODE
NORDMENDE 72, 73
NOKIA 74
PANASONIC 53, 54, 74, 75
PHILPS 06, 55, 56, 57
PHONOLA 06, 56, 57
PIONEER 58, 59, 73, 74, 75
RADIOLA 06, 56
RADIOMARELLI 57
RCA 45, 46
REX 74
SABA 57, 72, 73, 74, 75
SALORA 74
SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09
SANYO 41, 42, 43, 44, 48
SCHNEIDER 06
SELECO 74
SHARP 36, 37, 38, 39, 48
SIEMENS 71
SINGER 57
SINUDYNE 57
SONY 35, 48
TELEAVA 73
TELEFUNKEN 67, 73, 75, 76
THOMSON 72, 73, 75
THOMSON ASIA 80, 81
TOSHIBA 47, 48, 49, 50, 51, 52
WEGA 57
YOKO 06
ZENITH 63
4. If the TV turns off, setup is complete.
Enter other codes of the same brand if the first
code does not work.
5. To operate the TV, use the "TV Function Buttons"
described on page 10.
Important Note
• The remote may not be able to control every
model TV of the brands listed.
• If you replace the remote control's batteries, set
the brand code again.
ENG-38

Troubleshooting

Before requesting service (troubleshooting), please check the following.
Problem
• Check the batteries in the remote. They may need replacing.
No operations can be
• Operate the remote control at a distance of no more than 20 feet.
performed with the remote.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
• Ensure that the disc is installed with the label side facing up.
Disc does not play.
• Check the region number of the DVD.
5.1 channel sound is not
• 5.1 channel sound is reproduced only when the following conditions
being reproduced.
are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the "Dolby 5.1 ch" mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
The icon appears on • The features or action cannot be completed at this time because:
screen. 1. The DVD's software restricts it.
2. The DVD's software doesn't support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You've requested a title or chapter number or search time that is
out of range.
Disc Menu doesn't appear.
• Check if the disc has a Menu.
Play mode differs from the
• Some of the functions selected in the Setup Menu may not work
Setup Menu selection.
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot
• The Screen Ratio is fixed on your DVDs.
be changed.
• Make sure you have selected the correct Digital Output in the Audio
No audio.
Options Menu.
The screen is blocked • Press power on from a cold start with no disc in the unit.
Press the button on the front panel for 5 seconds.
The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language.
• Press power on from a cold start with no disc in the unit.
Forgot password
Press the button on the front panel for 5 seconds.
The SELECT MENU LANGUAGE display will appear. Select the
number button of the desired language. Press the MENU button,
and then press DOWN button to select Setup, then press RIGHT or
ENTER. Press Up or Down to select Parental Setup The Parental
Setup is now unlocked as indicated on the display.
You can change your password.
If you experience other • Go to the contents and find the section of the instruction book that
problems. contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
Action
Page
P5
P7
P11
P33
P15
P30~37
P35
P33
P35
P36~37
ENG-39