Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Adjusting the Audio Delay
When watching a DVD or other video source, the picture on the monitor may seem delayed with respect to the
sound. In this case, adjust the audio delay to delay the sound and synchronize it with the picture.
The audio delay setting is stored separately for each input source.
1
q Select the input source.
INPUT SELECTOR
(Main unit)
(Remote control unit)
w Set the input mode to "Auto".
INPUT
MODE
(Main unit)
(Remote control unit)
e Select Dolby/DTS Surround.
DOLBY
DTS
SURROUND
SURROUND
(Main unit)
(Remote control unit)
r Play a program source (DVD, etc.).
2
Press the SYSTEM SETUP button and display
the System Setup Menu screen.
(Remote control unit)
3
Select "Audio Delay" on the System Setup
Menu screen.
(Remote control unit)
4
Press jog stick "ENTER" to switch to the Audio
Delay adjustment screen.
(Remote control unit)
8
1-q
1-e
1-w
1-q
1-e
1-w
3, 4,
5, 6
2, 7
5
Set the delay time. (0 ms ~ 200 ms)
(Remote control unit)
With a movie source, for example, adjust so
that the movement of the actors' lips is
synchronized with the sound.
6
Press jog stick "ENTER" to return to the
System Setup Menu screen.
7
Press the SYSTEM SETUP button to complete
the setting.
NOTE:
The audio delay setting does not apply when playing
in the EXT. IN mode or in the analog input direct mode
or stereo mode (only when the crossover frequency is
set to "FIXED - THX" or front speaker is set to
"Large").
2 Differences in surround mode names depending on the input signals
Surround Mode
ANALOG
LINEAR PCM
DTS (5.1 ch)
C
C
PURE DIRECT, DIRECT
STEREO
C
C
HOME THX CINEMA
THX
THX
THX MTRX6.1
THX Ultra2 Cinema
THX Music Mode
THX5.1
DTS SURROUND
E
E
DTS ES MTRX
DTS SURROUND
DTS NEO:6
DTS NEO:6
DTS NEO:6
E
E
DOLBY DIGITAL
DOLBY PRO LOGIC
II
DOLBY
DOLBY
II
II
PRO LOGIC
PRO LOGIC
DSP SIMULATION
C
C
C : Selectable
: The surround mode name differs depending on the "MODE/SB CH OUT" surround parameter setting.
B : The surround mode name differs depending on the input signal.
E :
Not selectable
2 Other changes
1. CENTER IMAGE (0.0 to 0.5: default 0.2)
The center image parameter for adjusting the expansion of the center channel in the DTS NEO:6 MUSIC
mode has been added.
2. Subwoofer channel "OFF" setting
The subwoofer channel can now be set to "OFF" in all the surround modes.
"OFF" is set when the channel level is adjusted one step below -12 dB.
3. PURE DIRECT mode
The setting is now backed up.
4. Channel level and fader adjustment
• Channel selection
• Level adjustment and
fader adjustment
2 Playback using the DENON Link connector
Digital transfer and multi-channel playback of DVD audio discs and other multi-channel sources is possible by
connecting the AVR5800/AVC-A1SE to a Denon DVD player equipped with a DENON Link connector using
the connection cable included with the DVD player.
With discs on which special copyright protection measures have been taken, however, the digital signals may
not be output from the DVD player. In this case, connect the DVD player's analog multi-channel output to the
AVR5800/AVC-A1SE's EXT.IN-1 or EXT.IN-2 terminals for playback.
Also refer to your DVD player's operating instructions.
Input signals
DTS
DOLBY DIGITAL
DTS 96/24(5.1 ch)
DTS (6.1 ch)
D. D. (2 ch)
C
C
C
C
C
C
C
C
B
THX MTRX6.1
THX DSCRT6.1
THX
THX Ultra2 Cinema
THX MTRX6.1
THX Music Mode
THX5.1
B
E
DTS ES MTRX
DTS ES DSCRT6.1
DTS 96/24
DTS MTRX6.1
E
E
E
DTS NEO:6
E
E
E
E
E
E
E
DOLBY
PRO LOGIC
C
C
C
C
D. D. (5.1 ch)
C
C
THX SURROUND EX
THX Ultra2 Cinema
THX Music Mode
THX5.1
E
E
DOLBY DIGITAL EX
DOLBY DIGITAL
E
II
C
Publicité
Table des Matières
