Important - Philips 3000 Serie Mode D'emploi

EnGLIsH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
General description (Fig. 1)
A Hair clipping comb
B Length setting selector
C Cutting element
D On/off slide
E CHARGE light
F
Socket for appliance plug
G Adapter
H Appliance plug
I
Cleaning brush
J Beard trimming comb

Important

Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- Check if the voltage indicated on the adapter and on
the appliance corresponds to the local mains voltage
before you connect the appliance.
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
Caution
- Never immerse the appliance nor rinse it under the
tap.
- Do not use the appliance in the bath or in the
shower.
- Use, charge and store the appliance at a temperature
between 15°C and 35°C.
- Only use the adapter supplied to charge the
appliance.
- If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
- Do not use the appliance if the cutting element, the
hair clipping comb or the beard trimming comb is
damaged or broken, as this may cause injury.
- This appliance is only intended for clipping human
scalp hair and facial hair. Do not use it for any other
purpose.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientific
evidence available today.
Charging
Do not charge the appliance for more than 24 hours.
Charging takes approx. 10 hours.
When the appliance is fully charged, it has an operating
time of 40 minutes.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the appliance (Fig. 2).
3 Put the adapter in the wall socket.
The CHARGE light goes on to indicate that the
,
appliance is charging.
Note: The CHARGE light does not indicate when the
appliance is fully charged.
Optimising the lifetime of the rechargeable
batteries
Discharge the rechargeable batteries completely twice
a year by letting the motor run until it stops. Then fully
recharge the batteries.
2
Corded clipping
If the batteries are low, you can also use the
appliance from the mains.
Only use the appliance from the mains when the
rechargeable batteries are almost empty.
1 Switch off the appliance.
2 Connect the appliance to the mains and wait a few
seconds before you switch it on.
If the rechargeable batteries are completely empty, wait a
few minutes before you switch on the appliance.
Using the appliance
Clipping with hair clipping comb
Note: Make sure your hair is clean and dry. Do not use the
appliance on freshly washed hair.
1 Comb your hair with a styling comb in the
direction of hair growth. (Fig. 3)
2 Slide the hair clipping comb into the guiding
grooves of the appliance ('click') (Fig. 4).
Make sure that the arms of the comb have been properly
slid into the grooves on both sides.
3 Press the length setting selector (1) and then move
the hair clipping comb up or down (2) to set the
desired length setting (Fig. 5).
The corresponding hair length is visible on the side
,
of the comb.
Length settings
With the hair clipping comb attached, the appliance can
cut hair to 10 different lengths:
Hair lengths in mm Hair lengths in inches
3 1/8
5 3/16
7 9/32
9 3/8
11 7/16
13 1/2
15 5/8
17 21/32
19 3/4
21 7/8
4 Slide the on/off slide upwards to switch on the
appliance (Fig. 6).
5 Place the hair clipping comb on the scalp and move
the appliance through the hair slowly.
Tips
- Start clipping at the highest length setting of the
hair clipping comb and reduce the length setting
gradually.
- Write down the length settings you have used to
create a certain hairstyle as a reminder for future
clipping sessions.
- To clip in the most effective way, move the appliance
against the direction of hair growth.
- Since hair grows in different directions, you need
to move the appliance in different directions as well
(upward, downward or across) (Fig. 7).
- Make overlapping passes over the head to ensure
that the appliance catches all the hairs that need to
be cut.
- Make sure that the flat part of the hair clipping comb
is fully in contact with the scalp to obtain an even
clipping result.
- To achieve a good result with curly, sparse or long
hair, you can use a styling comb to guide the hair
towards the appliance.
- Regularly remove cut hair from the hair clipping
comb. If a lot of hair has accumulated in the comb,
remove it from the appliance and blow and/or shake
the hair out of it.
Clipping without hair clipping comb
You can use the appliance without hair clipping comb to
clip your hair very close to the skin, to a length of 1mm
(1/32 in) to contour the neckline and the area around
the ears.
1 To remove the hair clipping comb, press the length
setting selector (1), move the comb upwards and
then pull it off the appliance (2). (Fig. 8)
2 Comb the hair ends over the ears before you start
to contour the hairline.
3 Slide the on/off slide upwards to switch on the
appliance (Fig. 6).
4 Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends. (Fig. 9)
5 Only cut the hair ends. The hairline has to be close
to the ear.
6 To contour the neckline and the sideburns, turn the
appliance and make downward strokes (Fig. 10).
7 Move the appliance slowly and smoothly. Follow the
natural hairline.
Trimming with beard trimming comb
Note: Make sure your facial hair is clean and dry.
1 Comb your beard or moustache with a fine comb
before you start trimming.
2 Slide the beard trimming comb into the guiding
grooves of the appliance ('click') (Fig. 11).
Make sure that the arms of the comb have been properly
slid into the grooves on both sides.
3 Press the length setting selector (1) and then move
the beard trimming comb up or down (2) to set
the desired length setting (Fig. 12).
Length settings
With the beard trimming comb attached, the appliance
can cut hair to 8 different lengths:
Hair lengths in mm Hair lengths in inches
1.5 1/16
3.5 1/8
5.5 7/32
7.5 9/32
9.5 3/8
11.5 7/16
13.5 17/32
15.5 5/8
4 Slide the on/off slide upwards to switch on the
appliance (Fig. 6).
5 Place the beard trimming comb on the face and
move the appliance through the hair slowly (Fig. 13).
Tips
- When you trim your beard for the first time, start at
a length setting that is higher than the length of your
beard hairs and reduce the length setting gradually.
- To trim in the most effective way, move the appliance
against the direction of hair growth.
- Make overlapping passes over the chin to ensure
that the appliance catches all the hairs that need to
be cut.
- Make sure that the flat part of the beard trimming
comb is fully in contact with the face to obtain an
even trimming result.
- Regularly remove cut hair from the beard trimming
comb. If a lot of hair has accumulated in the comb,
remove it from the appliance and blow and/or shake
the hair out of it.
Creating a stubble beard
- To create a stubble beard, trim with the beard
trimming comb set to 1.5mm (1/16in).
4222.002.8144.1