Functional Description - Milwaukee 2645-20 Manuel De L'utilisateur

Functional Description

1. Quik-Lok tension lever
2. Transparent blade cover
3. Blade
4. Shoe cover
5. Shoe
6. Orbital action selector lever
7. Tilt angle scale
8. Shoe adjustment lever
9. Lock button
10. Trigger
WARNING
Recharge only with the
charger specifi ed for the battery. For specifi c
charging instructions, read the operator's
manual supplied with your charger and
battery. This tool is not compatible with V™-
technology or NiCd systems.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into
the body of the tool. Insert the battery pack until
the battery latches lock.
To remove the battery pack, press in both battery
latches and slide the battery pack off of the tool.
WARNING
To reduce the risk of injury,
always remove battery pack before changing
or removing accessories. Only use accesso-
ries specifi cally recommended for this tool.
Others may be hazardous.
Installing saw blades
Use only T-Shank jig saw blades.
1. Remove the battery pack.
2. Pull out and hold the Quik-Lok tension lever
(Fig. 1).
3. Fit the saw blade into the groove in the support
roller and push it fi rmly into the plunger as far
as it will go; the lug of the saw blade must be in
the plunger.
4. Release the Quik-Lok tension lever to secure
the saw blade.
All manuals and user guides at all-guides.com
9
10
1
2
6
3 5
4
ASSEMBLY
5. Check that the saw blade is held fi rmly; the slot
in the plunger will be at an angle to the blade
(Fig. 2).
Fig. 1 Fig. 2
Slot
Plunger
Lug
Using the anti-splinter device
The anti-splinter device helps
Fig. 3
stablize the workpiece and
Anti-splinter
reduce workpiece splinter.
device
1. Remove the battery pack.
2. Slide the anti-splinter de-
Shoe
vice onto the shoe (Fig. 3).
Make sure the anti-splinter
device is installed fl ush with
the bottom of the shoe.
NOTE: Do not use the transparent blade cover and
anti-splinter device when making bevel/angle cuts.
4
Using the shoe cover
The shoe cover is used to prevent marring and
scratching of the workpiece surface. To attach the
shoe cover:
1. Remove the battery pack.
2. Hook the front of the cover over the steel
shoe.
3. Snap the rear of the shoe cover over the back
of the shoe. Be sure both sides are snapped in
place.
4. When the shoe cover is not needed, remove
it by pulling the tabs on rear of the shoe cover
8
down. Unhook the front of the shoe cover and
remove.
7
Adjusting the shoe
The shoe may be tilted up to 45° in either direction.
To set a tilt angle for bevel/angle cuts:
1. Remove the battery pack.
2. Loosen the shoe adjustment lever and pull the
base forward slightly until the detents are not
engaged.
3. Tilt the shoe to the required preset angle
(0°, 15°, 30°, or 45°).
4. Push the shoe into the detent and tighten the
shoe adjustment lever.
5. To set an angle other than 0°, 15°, 30°, or 45°,
loosen the shoe adjustment lever and pull the
base forward slightly until the detents are not
Blade
engaged. Set the desired angle and tighten
the shoe adjustment lever without engaging a
detent. Make a test cut to verify the angle.
Fig. 4
OPERATION
WARNING
To reduce the risk of injury,
keep hands away from the blade and other
moving parts. Always wear safety goggles or
glasses with side shields. Use only specifi -
cally recommended accessories. Others may
be hazardous.
Starting and stopping the tool
1. To start the tool, grasp the handle fi rmly and
pull the trigger.
2. To vary the speed, increase or decrease pres-
sure on the trigger. The further the trigger is
pulled, the greater the speed.
3. To stop the tool, release the trigger. Allow the
tool to come to a complete stop before remov-
ing the blade from a partial cut or laying the
tool down.
Locking the trigger
To lock the trigger, push the trigger lock from the
lock side of the tool. The trigger will not work while
the switch is in the locked position. Always lock the
trigger and remove the battery pack before perform-
ing maintenance and changing accessories. Lock
the trigger when storing the tool and when the tool
is not in use.
To unlock the trigger, push the trigger lock from the
unlock side of the tool.
Adjusting the orbital action
The amount of orbital action may be adjusted with
the orbital action selector lever. In general, a large
orbital action (4) should be used with soft materials
and a no orbital action (0) should be used with hard
materials. When a smooth cut is required, no orbit
(0) should be used.
Material Orbital Action
Wood 0-4
Metal 0-1
Aluminum 0-1
Plastic 0-2
Smooth Cut 0
5