Bulb Replacement; Troubleshooting Guide - Health Zenith Secure Home DualBrite SH-5597 Mode D'emploi

Bulb Replacement

CAUTION: When replacing the bulb, turn power
off and let the fixture cool.
Important: Use a clean glove or cloth when handling
the new bulb. Use isopropyl (rubbing) alcohol to clean
the bulb if it is touched with your bare hands.
1. To remove lamp shade, loosen screw 2 full turns
with a small phillips-head screwdriver. Turn shade
counterclockwise and remove.
2. To remove bulb, pull straight out of fixture.
3. To replace bulb, push bulb pins into lamp socket.
Check that the bulb is seated properly.
4. To reinstall lamp shade, place shade on fixture and
align notches on shade with tabs on fixture. Turn
clockwise. Tighten screw firmly.
SYMPTOM POSSIBLE CAUSE
Lights will 1. Light switch is turned off.
not come on.
2. Light is loose or burned out.
3. Fuse is blown or circuit breaker is
turned off.
4. Daylight turn-off is in effect (Recheck
after dark).
5. Incorrect circuit wiring, if this is a new
installation.
6. Re-aim the sensor to cover desired
area.
Lights come
1. Light control may be installed in a
on in day-
relatively dark location.
light.
2. Light control is in TEST. (Set control
switch to an ON-TIME position).
Lights come 1. Light control may be sensing small
animals or automobile traffic. (Re-aim
on for no
apparent sensor).
reason. 2. RANGE is set too high. (Reduce
RANGE).
3. D
ual
Lights turn
1. Sensor is in a relatively dark location.
off too late
(Relocate sensor, or use 3 hr or 6 hr
in Dusk-to-
setting).
Dawn setting.
598-1162-04

TROUBLESHOOTING GUIDE

B Timer is on.
®
rite
SPECIFICATIONS
Horizontal Range . . . . Up to 70 ft. (21 m); 100 ft.
Vertical Range . . . . . . Up to 15 ft. (4.6 m)
Sensing Angle . . . . . . Up to 240° horizontal. Up to 80°
Electrical Load . . . . . . Up to 200 Watt Maximum Tung-
Power Requirements . 120 VAC, 60 Hz
Operating Modes . . . . TEST, AUTO, and MANUAL
Time Delay . . . . . . . . 1, 5, 20 minutes
D B Timer . . . . 3, 6 hours, Dusk-to-Dawn
®
ual rite
Replacement bulb . . . T4 100W, G8 halogen bi-pin 120
HeathCo LLC reserves the right to discontinue prod-
ucts and to change specifications at any time without
incurring any obligation to incorporate new features in
products previously sold.
SYMPTOM POSSIBLE CAUSE
Lights stay 1. A bulb is positioned too close to the
on continu-
sensor or pointed at nearby objects
ously.
that cause heat to trigger the sensor.
(Reposition the bulb away from the
sensor or nearby objects).
2. Sensor is pointed toward a heat source
like an air vent, dryer vent, or brightly-
painted heat-reflective surface.(Repo-
sition sensor. Reduce RANGE).
3. Light control is in Manual Mode. (Switch
to Auto).
Lights flash
1. Heat or light from the bulbs may be
on and off.
turning the light control on and off.
(Reposition the bulbs away from the
sensor).
2. Heat being reflected from other objects
may be affecting the sensor. (Reposi-
tion sensor).
3. Light control is in the TEST mode and
warming up. (Flashing is normal under
these conditions. Turn BOOST off).
Lights flash
1. Sensor is detecting its own lights.
once, then
(Reposition bulbs to keep area below
stay off in
the sensor relatively dark).
Manual Mode.
5
(30.5 m) with Range Boost.
[var ies with surrounding
temperature]
Vertical
sten Halogen [Up to 100 Watt
Maximum each bulb holder.]
MODE
VAC