Radio Reception - Bosch BLAUPUNKT KEY LARGO DM2000 Mode D'emploi

Radio Reception

Seek Tuning
1.
Press the to select the desired AM or FM band.
BND / TS
FM I FM II FT AM (A) AT
(FT & AT are Travel Store bands.)
2.
Press the to tune in stations. Tuning automati-
TUN/ TRK
cally stops at a broadcasting frequency.
" SEEK " indicator will appear on the display window.
When tuned in to FM stereo broadcasting stations, the
" " stereo signal indicator will appear on the display
window.
Manual Tuning
1.
Press the to select the desired AM or FM band.
BND / TS
2.
Press the or for more than 0.5 sec-
TUN/ TRK TUN/ TRK
ond to activate the manual tuning mode. Press again to
tune in to stations.
" MANUAL " indicator will appear on the display window.
After 4 seconds of completing Manual Tuning, the tuning
control will revert to the Seek Tuning mode.
Scan Tuning
1.
Press the to select the desired AM or FM band.
BND / TS
2.
Hold the pressed for less than 2 seconds.
SC/PS
The unit will scan the selected band for stations.
" SCAN " indicator will appear on the display window. The
unit will stop at each station for 8 seconds, before con-
tinuing to the next station.
Press the again to stop Scan Tuning and remain
SC/PS
this on the selected frequency.
Tip
While tuning, the pie-shaped signal-strength meter
on the display is lit differently depending on the strength
of the signal. While scanning bands, the pie-shaped sig-
nal-strength meter spins. While playing CD's, this display
spins also.
Key Largo (Eng) p.1-13
Preset Scan Tuning
1.
Press the
BND / TS
2.
Hold the
SC/PS
" SCAN " indicator will appear on the display window.
The unit will scan preset memory for the 12 stations from
the AM/AT band or the 18 stations from the FM I/FM II/
FT bands. The unit will stop at each preset station for 8
seconds, before continuing to the next preset station.
Press the
SC/PS
remain this on the selected frequency.
Memorizing Stations Automatically (Travel Store)
1.
Press the
BND / TS
2.
Hold the
BND / TS
Up to 6 stations with strong signals will be automatically
stored in preset memory for the selected band.
If the radio is in FM I or FM II, it switches to FT. If the
radio is in AM, it switches to AT.
Note
This function is available for FT and AT.
Memorizing Only the Desired Stations
You can store up to 6 stations on each band (18 for FM I, FM
II and FT, 12 for AM and AT) in the order of your choice.
1.
Press the
BND / TS
2.
Press the
TUN/ TRK
3.
Press and hold the desired preset memory button
for about 2 seconds until the frequency indicator
6
flashes twice.
The number of the pressed preset memory button ap-
pears on the display window.
Note
If when you store another station on the same preset number
button, the previously stored station is replaced with new one.
5
to select the desired AM or FM band.
pressed for more than 2 seconds.
again to stop Preset Scan Tuning and
to select the desired AM or FM band.
pressed for longer than 2 seconds.
to select the desired band.
to tune in stations.
-
1
6/19/00, 10:02 AM
Receiving the Memorized Stations
1.
Press the to select the desired AM or FM band.
BND / TS
2.
Press the momentarily.
1 6
Local/Distant (LO/DX) Selection
This feature is used to select the signal strength at which the
radio will stop during Seek Tuning.
Press the for more than 2 seconds to select the
MUTE / SENS
Local setting and only strong (local) stations will be received.
The " lo " indicator appears on the display window.
Pressing for more than 2 seconds again will select the Dis-
tant setting and the radio will stop at a wider range of signals,
including weaker more distant stations. The " lo " indicator will
go out on the display window. DX is the suggested default
setting.
E-5