Registres Modbus - Sentera Controls ODMFM-R Instructions De Montage Et Mode D'emploi

ODMFM-R
VÉRIFICATION DES INSTRUCTIONS D'INSTALLATION

REGISTRES MODBUS

INPUT REGISTERS
1 Temperature reading
2 Relative humidity level
3 Dew point
4 CO level
2
5 Ambient light intensity
6 Active / standby
7—10
Output value 1
11
(temperature)
Output value 2 (relative
12
humidity)
13 Output value 2 (CO )
2
14 Temperature alert flag
15 Relative humidity alert flag
16 CO alert flag
2
17 Temperature range limit flag unsigned int.
Relative humidity range
18
limit flag
19 CO range limit flag
2
Humidity / temperature
20
sensor fault
21 CO Sensor fault
2
22 Ambient light sensor fault
MIW-ODMFM-R-FR-000 - 16 / 04 / 18
TRANSMETTEUR
MULTIFONCTIONNEL AMBIANTE
Si votre appareil ne fonctionne pas comme prévu, vérifiez les raccordements.
Data type Description
signed int. Actual temperature level
unsigned int. Actual relative humidity level
signed int. Calculated dew point
unsigned int. Actual CO level
2
unsigned int. Measured light intensity
Active or Standby indication according the Active /
Standby light level defined via holding registers 34
unsigned int.
and 35. If the measured light level is between the
two levels the indication is 0 (Low intensity)
Reserved, return "0".
unsigned int. Output value for temperature (T )
unsigned int. Output value for relative humidity (rH)
Output value for CO
2
Flag indicates that measured temperature is outside
set alert values. Set to '1' when the measured value
unsigned int.
is outside the temperature alert values defined by
holding registers 20 and 21
Flag indicates that measured relative humidity
is outside set alert values. Set to '1' when the
unsigned int.
measured value is outside the relative humidity alert
values defined by holding registers 22 and 23.
Flag indicates that measured CO
alert values. Set to '1' when the measured value is
unsigned int.
outside the CO values defined by holding registers
2
24 and 25
Flag indicates that measured temperature is outside
set range limit values. Set to '1' when the measured
value is outside the temperature range limit values
defined by holding registers 14 and 15
Flag indicates that measured relative humidity is
outside set range limit values. Set to '1' when the
unsigned int.
measured value is outside the relative humidity limit
range values defined by holding registers 16 and 17
Flag indicates that measured CO
range limit values. Set to '1' when the measured CO
unsigned int.
is outside limit range values set defined by holding
registers 18 and 19
Flag indicates if the communication with the
unsigned int.
temperature and humidity sensor is lost.
Flag indicates if the communication with the CO
unsigned int.
sensor is lost
Flag that shows if the communication with the
unsigned int.
ambient light sensor is lost
Retour à la Table des matières
Data
-300—700
0—1.000
-700—700
0—2.000
0—32.000
0—1.000
0—1.000
level is outside set
2
is outside set
2
2
2
www.sentera.eu
Values
500 =
1.000 =
200 =
2.000 =
1.000 =
0 =
0—2 1 =
2 =
0 =
1.000 =
0 =
1.000 =
0 = Measured temperature is OK
0—1
1 = Measured temperature is too high/ low
0 =
0—1
1 = Measured rH is too high/ low
0 =
0—1
1 = Measured CO
0 = Temperature range is OK
0—1
1 = Temperature range is too high/ low
0 =
0—1
1 = rH range is too high/ low
0 =
0—1
1 = CO range is too high/ low
2
0 =
0—1
1 =
0 =
0—1
1 =
0 =
0—1
1 =
50,0 °C
100,0 % rH
20,0 °C
2.000 ppm
1.000 lx
Low light intensity
Active
Standby
0 %
100 %
0 %
100 %
Measured rH is OK
Measured CO is OK
2
is too high/ low
2
rH range is OK
CO range is OK
2
No
Yes
No
Yes
No
Yes
8 - 10