Locinox Valentino Manuel De Configuration page 7

2.3 MANAGE PIN CODES [1]
• Access programming mode (see 2. 1 )
A maximum of 100 different PIN codes can
be programmed (4-8 digits)
EN
• Press [1] and confirm with [#]
• [1] and [#] are both lit
• Enter a new PIN code and confirm with [#]
• In case of a new code, the code will need to be
repeated and confirmed with [#]
• The lights below button [3] and [8] are indicating
on which side of the lock the code is valid. [8] is
used for the side the user is currently using, while
[3] is used for the other side
• Pressing [3] and [8] will select (permanently on) or
de-select (flashing) the corresponding side
• Press [#] to confirm
• You will return to the main menu of the
programming mode
When two different codes or a wrong code
length is entered, all keys will flash three times,
indicating the code setting hasn't been saved.
Try again. [1] will remain lit
A code can be removed by de-selecting [3]
and [8] before confirmation
2.4 MANAGE PERMANENTLY OPEN
CODES [2]
PIN codes generated using menu [1] (manage PIN
codes) will unlock the lock for a predefined duration,
as configured in menu [3] ('setup switching duration').
In contrast, a 'permanently open' code has no
predefined duration to remain open, but will remain
open, until the same code (or another permanently
open code) is entered.
• Access programming mode (see 2. 1 )
• Press [2] and confirm with [#]
• [2] and [#] are both lit
• Enter a new PIN code and confirm with [#]
• In case of a new code, the code will need to be
repeated and confirmed with [#]
• The lights below button [3] and [8] are indicating
on which side of the lock the code is valid. [8] is
used for the side the user is currently using, while
[3] is used for the other side
• Pressing [3] and [8] will select (permanently on) or
de-select (flashing) the corresponding side
7
• Press [#] to confirm
• You will return to the main menu of the
programming mode
When two different codes or a wrong code
length is entered, all keys will flash three times,
indicating the code setting hasn't been saved.
Try again. [2] will remain lit
A code can be removed by de-selecting [3]
and [8] before confirmation
2.5 SETUP SWITCHING DURATION [3]
• Access programming mode (see 2. 1 )
• Press [3] and confirm with [#]
• [3] and [#] are both lit
• Enter a value between 1 and 99, and confirm with
[#]. When all leds flash, your choice is saved
• You will return to the main menu
In case an invalid time is entered, all keys will
flash three times. Menu [3] remains activated
The default time is set at 8 seconds
2.6 SETUP FREE EXIT MODE [4]
The free-exit mode menu allows configuring a side
of the lock in 'free exit mode'. On the free-exit side,
entering a PIN code is not required: just pressing any
key will unlock the lock for a predefined duration.
• Access programming mode (see 2. 1 )
• Press [4] and confirm with [#]
• [4] and [#] are both lit
• The lights below button [3] and [8] are indicating
which side of the lock is configured in free exit-
mode. [8] is used for the side the user is currently
using, while [3] is used for the other side
• Pressing [3] or [8] will select (permanently on) or
de-select (flashing) the corresponding side to be
configured in free-exit mode
• The selection is confirmed by pressing the [#] key
• You will return to the main menu of the
programming mode
The free-exit mode can be disabled by
de-selecting [3] and [8] before confirmation
Valentino