Hoover H-ENERGY 700 Manuel D'utilisation page 5

CLEANER MAINTENANCE
Both full bag check and filter cleaning indicators are signaled by a red light on the display.
Replacing the Dust Bag
Please check the bag, if necessary, replace it.
Press the bag door release latch and open the bag door. [11]
1.
Lift the handle of the bag holder up. [12]
2.
3. Hold the bag with the holder over a dust bin. Press the red button to automatically
release the bag without any contact with dust. [13]
4. Fold a new bag and insert the collar into the bag holder. [14,15]
5. Refit the bag with holder back into the appliance. [16]
6. Close the bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag holder are not
assembled to the cleaner. Always ensure the bag is present when closing the bag door.
REMEMBER: The bag check indicator also turns red onto the display [D] if an obstruction
has occurred. In this case refer to 'Remove a Blockage from the System'.
Cleaning the Filters
To ensure constant optimum cleaning performances, please wash the filters when the
filter indicator red light is on and then press the MANUAL MODE activation button for 3
seconds to turn off the red indicator light.
Cleaning the pre-motor filter:
1. Lift the bag door release latch to open bag door and remove the bag. [11,12]
2. Remove the pre-motor filter frame from the cleaner. [19]
3. Remove the filter from the pre-motor filter frame. [20]
4. Wash the pre-motor filter and the pre-motor filter frame using warm water, and allow
it to dry thoroughly before inserting into the cleaner. [20,21]
Cleaning the exhaust filter:
1. Unclip the exhaust filter cover and remove the exhaust filter pack. [17,18]
2. Wash the exhaust filter pack under warm water, and allow it to dry thoroughly before
inserting into the cleaner. [20,21]
Remember: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover replacement. Do not try and use product
without dust bag or filters fitted.
Cleaning the permanent cloth dust bag* (*Certain model only)
To maintain optimum performance we recommended that you wash the permanent cloth
dust bag after every 5 full bags. Empty the contents of the bag into a bin, wash the bag
under warm water, remove excess water and leave to dry fully before replacing.
Removing a blockage from the system
If the bag check indicator remains lit on the display [D]:
1. Check if the bag is full. If so refer to 'Replacing the Dust Bag'.
2. If it is not full, then
*Certain Models Only ** May vary according to model
A. Do the filters need cleaning? If so refer to 'Cleaning the Filters'.
B. Check if there is any other blockage in the system.
- Use a cord or a stick to remove any blockage from the telescopic tube or flexible
hose. Warning - The bag check indicator will remain red if the cleaner is used when
the bag is full, if there is a blockage or if the filters are dirty. If the cleaner is used for
a significant period of time with the bag check indicator illuminated, an thermal cut
out will switch the cleaner off to prevent overheating. The bag check indicator turns
off once the cleaner has switched off to signal that the thermal cut out has been
activated. If this should happen, switch the cleaner off, unplug and correct the fault.
It will take about 30 minutes for the cut out to automatically reset.
Replacing the battery of the handle remote control* [22]
If the remote controls on the handle do not respond when pressing any buttons, please
change the battery:
1. Use screw driver to release remote control from handle.
2. Remove the exhaust battery by pushing aside the clip and replace with a new one.
Use only battery type Lithium CR2032 3V.
ACCESSORIES
To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
Integrated Accessories on Hi-Controller Handle with Settings**
This handle features convenient integrated accessories:
-
Built-in Crevice Tool: The hose handle end can be used as a crevice tool to reach
narrow spaces.
-
Furniture Tool: Press the latches on both sides of the handle and slide downwards to
release the furniture tool to clean soft surfaces and textiles (curtains, upholstery). [S1]
-
Dusting Brush: Press the latches on both sides of the and slide downwards then
push the slider to the end to release the built-in dusting brush. Ideal for hard surfaces
(bookshelves, keyboards, skirting boards). [S1]
Mini Turbo Dual Action Allergen Remover Nozzle* – Use the mini turbo nozzle on
stairs or for deep cleaning on textile surfaces and other hard to clean areas, particularly
suitable for allergen removal. [T]
Long 2in1 Tool* – Crevice tool and dusting brush - It allows to clean hard-to-reach areas
such as bookshelves and high corners. [U] It can be fitted to the end of the hose handle
or to the end of the fixed tube.
Parquet Extra Care nozzle* – For parquet floors and other delicate floors. [V]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
3
GB