DeWalt DW263 Traduction De La Notice D'instructions Originale page 22

EngLIsh
Your DW274KN/DW275KN features a silent clutch function.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These screwdrivers are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Dead Spindle Drive Clutch
This screwdriver is equipped with a dead spindle feature; the
spindle does not turn until the fastener is pressed into the
workpiece. This enables fasteners to be placed onto the drive
accessory of a running screwdriver.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
20
WALT
e
2 ; the maximum length
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Fitting and Removing 1/4" Hex Drive
Accessories
Your D WALT screwdriver has a 1/4" hexagonal drive system.
e
The drive accessory is retained in the holder by a ball and a
spring which engages in a groove in the accessory shank.
DW263/DW264/DW274/DW274KN/
DW275/DW275KN (Fig. B)
1. Remove the collar 4 by pulling it forward.
2. Select the required accessory (both models) and matching
depth locator 5 when using a nutsetter (DW263/DW264).
3. To insert the accessory 12
push it into the holder until it snaps in place. Tap it lightly
8
if required.
4. To remove the accessory, pull it out of the holder using a
pair of pliers.
5. Reinstall the collar by aligning the ribs
4
the collar 4 with the grooves
snap the collar in place.
DW268/DW269 (Fig. A2)
1. Pull the ball retainer 7 to the front and hold it.
2. Insert the accessory.
3. Release the ball Retainer.
Replacing the bit tip (Fig. B)
Simply pull out the bit tip 11 . A pair of pliers may be required.
Driving Depth (Fig. C)
DW263/DW264/DW274/DW274KN/
DW275/DW275KN
The depth sensitive feature offers the following advantages:
• The selected driving depth is repeatable for structural
integrity.
• Screws with sealing washers are driven correctly so that no
leaks occur.
Setting the Driving depth
The driving depth is determined by the position of the depth
locator 5 in relation to the bit or socket.The symbols on the
collar indicate how to set the driving depth.
4
• Turn the collar 4 clockwise to increase the driving depth.
• Turn the collar 4 counterclockwise to decrease the driving
depth.
Versa Clutch® Units
DW268/DW269 (Fig. A2)
External adjustment of all Versa Clutch® units for a wide range of
fastener sizes is fast and easy, as follows:
, e.g., a bit holder or nutsetter,
on the inside of
9
10 in the clutch housing and