Monacor AXC-2036BF Manuel page 3

AXC-2036BF
Order Number 18.4550
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
TVI/AHD Surveillance Camera
These instructions are intended for installers of video
surveillance systems. Please read the instructions
carefully prior to installation and keep them for later
reference.
1 Applications
This high-resolution colour camera is specially designed for
use in video surveillance systems (CCTV). The HD-TVI tech-
nology (High Definition Transport Video Interface) supports
transmission of high-resolution analog video signals (1080p)
via standard coaxial cables with a maximum length of 300 m.
In addition, the camera is equipped with an AHD video signal
output which can be switched to composite signal format.
The rugged metal housing of the camera is weatherproof
(IP 66) and therefore also suitable for outdoor applications.
The camera features include automatic white balance, digital
noise suppression and other functions to be configured via
OSD menu. The menu can only be remote-controlled by
means of a video recorder with COC protocol. In the dark,
the IR LEDs will illuminate a surveillance zone of up to 30 m,
the IR filter will be deactivated and the camera will switch
to B/ W mode.
2 Important Notes
The camera corresponds to all relevant directives of the EU
and is therefore marked with .
•
Protect the camera against extreme temperatures
(admissible ambient temperature range: −10 °C to +50 °C).
•
When cleaning the housing, never use aggressive deter-
gents or chemicals.
•
No guarantee claims for the camera and no liability for
any resulting personal damage or material damage will
be accepted if the camera is used for other purposes than
originally intended, if it is not correctly installed, or if it is
not repaired in an expert way.
If the camera is to be put out of operation defini-
tively, take it to a local recycling plant for a disposal
which is not harmful to the environment.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
3 Installation
1) Make a test run first to find the best mounting location.
2) At the mounting location (e. g. wall or ceiling), drill three
holes for fixing the base (4) and, if necessary, drill a hole
for the connection cable (alternatively, the cable can
be guided through one of the cable inlets on the side
of the base). Fasten the base at the mounting location.
If required, release the nut (3) of the camera support.
3) Connect the BNC plug TVI (6) to the input of an HD-TVI
compatible video recorder (e. g. TVR series from MONA-
COR) or/and connect the BNC plug AHD (7) to the input
of an AHD compatible video recorder or monitor.
The AHD output (7) can be switched to composite sig-
nal format: Keep the pushbutton (8) pressed for more
than 5 seconds. To return to the AHD signal, press the
pushbutton briefly.
4) Connect a regulated 12 V power supply unit with a per-
manent rating of 450 mA to the inline jack POWER (9).
A low-voltage plug 5.5 / 2.1 mm (outside / inside diameter)
is required. Always observe the correct polarity (centre
contact = +).
CAUTION The infrared LEDs will switch on when dark-
ness falls. When setting up the camera, never look di-
rectly into the lit infrared LEDs from a close range. The
infrared light may cause eye irritation. However, the
infrared radiation is far below the emission limit and
rated risk-free according to EN 62471.
5) For outdoor installation please note:
The connections (6 – 9) and the cable splitter (5) are not
weatherproof; protect them accordingly.
6) Switch on the video recorder and the monitor connected
and align the camera by means of the image on the
monitor: Release the nut (3) and position the camera as
desired. Then fasten the nut again.
7) To protect the lens against direct sunlight, place the sun-
shield (1) on the camera and fasten it with the locking
screw (2).
1 2
4 Settings via OSD Menu
The camera settings can be changed via an OSD menu which
is operated via PTZ remote control from the video recorder.
The control is made by means of the COC protocol via the
video cable.
To activate the OSD menu, send the control command
"Iris +" or call up "Preset 95". The main menu will appear:
MAIN MENU
1. LENS MANUAL
↲
2. EXPOSURE
3. BACKLIGHT OFF
4. WHITE BAL ATW
↲
5. DAY&NIGHT EXT
↲
6. NR
↲
7. SPECIAL
↲
8. ADJUST
↲
9. EXIT SAVE&END
To select a menu item, make control commands for the
vertical movement (Tilt:  , ); to change the value or to
select an option, make control commands for the horizontal
↲
movement (Pan: , ). When the symbol appears behind
a menu item or an option, the command "Iris +" (corre-
sponding to "Enter") can be used to call up a submenu or
to activate a function.
All setting options can be found in the table on the back
of these instructions. These instructions refer to the preset
English menu; to change the menu language, go to
↲ 
.
CIAL 5. LANGUAGE
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
3 4 5
TVI
To exit the menu, use  or  in the line
↲ (to save the changes) or
option
SAVE&END
cancel the changes) and confirm with "Iris +".
To reset all settings to the factory settings, use  or  in
the line to select the option
EXIT RESET
"Iris +". The menu language selected will remain the same
after a reset. Save the settings when exiting the menu.
5 Specifications
Image sensor: . . . . . . . . . . .CMOS chip, 8.5 mm (1⁄3 ")
Number of pixels: . . . . . . . .1920 × 1080 max.
Resolution: . . . . . . . . . . . . .1080P/ 25
Colour modulation system: .PAL
Lens: . . . . . . . . . . . . . . . . . .3.6 mm /1 : 1.2
Electronic shutter: . . . . . . . .1⁄50 – 1⁄50 000 s
Video output: . . . . . . . . . . .1 V (pp) / 75 Ω
IR LEDs, range: . . . . . . . . . .42 LEDs, 30 m
Power supply: . . . . . . . . . . . ⎓ 12 V ±10 %, 450 mA
Ambient temperature: . . . .−10 °C to +50 °C
IP rating: . . . . . . . . . . . . . . .IP 66
Dimensions: . . . . . . . . . . . . ⌀ 87 mm × 219 mm
Weight: . . . . . . . . . . . . . . .250 g
7. SPE-
Subject to technical modification.
A-1767.99.01.05.2016
VIDEO OUT: TVI
6
VIDEO OUT: AHD/CVBS
7
SELECTION: AHD/CVBS
8
12V
9
EXIT to select the
↲ (to
NOT SAVE
↲ and confirm with