Kong PAMIR FAST 946.000 Information De Produit

8 - SPECIFIC INFORMATION
The category III Personal Protective Equipment 946.000 "PAMIR" is:
- two sheaves per device mounted in a bracket used to link a rope or an
accessory cord to a connector reducing the friction while the rope or
accessory cord is moving under load;
- self-closing Mobile Connecting Devices not automatically self-locking,
only when used with the protection (D);
- part of a system protecting against impact caused by fall from a height;
- certified according to EN 12278:07 and EN17109:2020 type A.
Fig. 1 –Attachment point (E) – It is recommended the use of a connector
with a gate locking device.
Fig. 2 – Protection (D) installation – The cap protection (D) is an
accessory designed to avoid finger entrapment, an hazard common with
pulleys.
Fig. 3 – Use as pulley – When assembling the system take in account
the breaking Load of device (BL=30kN or 6750lb), its Working Limit Load
(WLL=8kN), and also a Safety Factor chosen by the user.
Fig. 4 – Use as shuttle in rope courses – Attach this device to the safety
line before connecting the Individual Safety System.
Fig. 5 – Example of wrong and dangerous use.
Fig. 6 – Force composition - By reducing the deflection in a cable/rope
(therefore widening the angle α), the forces acting on the anchoring points
exponentially increase.
Compatibility – This device has been designed to be used with:
- cables and ropes with diameter less than 13mm;
- connectors according to EN362 and/or EN12275;
When used in Individual Safety Systems for rope courses according
to EN15567-1, it is suitable to create ZAZA1 series or ZAZA2 series of
Individual Safety Systems. It also is required:
- the use of the protection (D);
- that all connection in the user reach between this device and
its lanyard shall only openable with a tool (a lark's foot of is
considered not openable).
Check before and after use - Before and after use, make sure that
the device is in an efficient condition and that it is working properly, in
particular, check that:
- is suitable for the use you intend to make of it;
- the sheaves (B) rotate freely;
- has not been mechanically deformed;
- shows no sign of cracks, wear, corrosion and oxidation;
- the rope/cable does not scratch the bracket (A);
PAMIR FAST
946.000
PAMIR FAST
- markings are still readable.
Before use, find a completely safe position and carry out movements and
suspension tests to check that this device is correctly positioned on the
rope/cable.
Important:
- This device by itself is not intended to limit the deceleration of the fall of
the user, as defined in EN 15567-1, for this requirement it is essential to
consider the whole ropes course system;
- During use check that:
- The devices attached are correctly positioned;
- This device is free to position itself in the proper direction for
hauling the load.
Warning:
- Beware of entrapment;
- The maximum speed allowed for this device is 15 m/s;
- It is forbidden the use on the Via Ferrata, unless specially designed;
- Use the protection (D) and wear personal protective equipment such as
gloves and helmet to protect from burns, crushing and to avoid trapping
fingers or hair between the rope/cable and the sheaves (B);
- The potential falling height must always be lower than 0.5 m unless the
user is equipped with suitable certified devices (eg. Energy absorbers
according to EN355) that protects from dynamic forces exerted on the
user during the arrest of a fall.
NOMENCLATURE • NOMENCLATURA
B
A
E
C
F D
EN: (A) Bracket in aluminium alloy, (B) Sheaves in mild steel with
ball bearings, (C) Stainless steel pins, (D) Polyamide protection, (E)
Attachment point, (F) Auxiliary attachment hole.
IT: (A) Staffa in lega di alluminio, (B) Carrucola in acciaio dolce con
cuscinetti a sfere, (C) Perni in acciaio inossidabile, (D) Protezione in
poliammide, (E) Punto di fissaggio, (F) Foro di fissaggio ausiliario.
FR: (A) Support en alliage d'aluminium, (B) Poulies en acier doux avec
roulements à billes, (C) Axes en acier inoxydable, (D) Protection en
polyamide, (E) Point de fixation, (F) Trou de fixation auxiliaire.
DE: (A) Halterung aus Aluminiumlegierung, (B) Umlenkrollen aus
Baustahl mit Kugellagern, (C) Stifte aus Edelstahl, (D) Polyamid-Schutz,
(E) Befestigungspunkt, (F) Hilfsbefestigungsloch.
ES: (A) Soporte en aleación de aluminio, (B) Poleas en acero dulce con
rodamientos de bolas, (C) Pasadores de acero inoxidable, (D) Protección
de poliamida, (E) Punto de unión, (F) Orificio de fijación auxiliar.
NOMENCLATURE • TERMINOLOGIE • NOMBRES
Master text
1
E
E
3
4
6
KEEP IN MIND FORCE COMPOSITION!
2
D
E
F
COMPACT HOIST
0.3 kN
0.6 kN
1 kN 1 kN
5
A
D
F
BL WLL
30 kN 8 kN
7.5 7.5 7.5 7.5 2 2 2 2
kN kN kN kN kN kN kN kN
1 kN =
102 kgf