KRESS KUX15P Mode D'emploi page 7

VIBRATION INFORMATION
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration
Mode description
emission value
Hammer drilling a =11.674
h,HD
into concrete m/s
2
a
chiseling
h,Cheq
m/s
2
The declared vibration total value may be used for
comparing one tool with another, and may also be used
in a preliminary assessment of exposure.
WARNING:The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the
tool is used dependant on the following examples and
other variations on how the tool is used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring
it is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING:To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
Uncertainty K
K = 1.5 m/s²
=12.214
K = 1.5 m/s²
OPERATION
INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
Intended Use
The machine is intended for hammer drilling in concrete,
brick and stone as well as for light chiseling work. It is
also suitable for drilling without impact in wood, metal,
ceramic and plastic.
WARNING: Remove the plug from
the socket before carrying out any
adjustment, servicing or maintenance.
1. Inserting/Removing bits
Take care that the dust protection cap is not damaged
when changing tools.
1) Inserting bits (See Fig. A)
Clean and lightly grease the bit with the oil provided
before inserting. Retract back the bit holder locking
sleeve (a) and insert the dust-free bit into the bit holder
with a twisting motion until it latches.
The bit locks itself. Check the locking by pulling on the
tool.
2) Removing bits (See Fig. B)
Retract back the bit holder locking sleeve (a) and pull
out the bit.
WARNING! Your new KRESS Rotary
Hammer generates powerful forces to get
your job done quickly and effectively. These
forces may cause inferior quality SDS bits
to break and jam in the chuck. We therefore
recommend that only high quality SDS bits be
used with this tool.
2. Adjusting the auxiliary handle (See Fig. C)
Loosen the depth gauge by rotating the handle counter-
clockwise. Slide the depth gauge until the distance
between the depth gauge end and the drill bit end is
equal to the depth of hole/screw you wish to make.
Then clamp the depth gauge by rotating the handle
clockwise.
WARNING: Always use the auxiliary
handle.
3. Anti-vibration handle
The Anti-vibration handle reduces the vibration
generated when operating the machine to ensure safe
and comfortable operation.
4. Starting/Stopping
Depress the On/Off switch to start and release it to stop
your tool.
5. Continuous operation
Starting: keep holding the On/Off switch to ensure
continuous operation.
Stopping: release the On/Off switch.
6. Function mode selection
The operation of the gearbox for each application is
set with the function mode selection switch. To change
between functions, depress the unlocking button and
rotate the selector to the desired operating mode.
7
EN