Canarm XFS Serie Mode D'emploi

Instruction Manual for "XFS" Light
Commercial Wall Exhaust Fans
"XFS" Light Commercial Wall Exhaust Fans
Read Instructions Completely Before Installation & Save For Reference
Congratulations on the purchase of your quality built direct drive, wall exhaust ventilation fan. Used for general exhaust ventilation, these
fans come fully assembled and 100% of fans are tested for proper operation before shipping.
"XFS" Exhaust Fans:
These models have a rugged, welded steel box housing with a powder coated finish and aluminum exhaust louvers. The louvers open
automatically when the fan starts up and close when the fan stops.
INSTALLATION
Installation is fast and simple. A sturdy framed wall opening should be prepared in advance to the size indicated for your fan in the charts
above. With lag bolts for wooden frames or nut, bolt and lock washers for steel frames, secure the fan using the four mounting holes
provided, one in each corner of the fan.
OPERATION
The fan has a cord and grounded plug. Plug the fan into a 115 Volt socket. Use the pull chain to turn fan off and adjust speed.
!
WARNING
WARNING: FAN IS GUARDED ON INTERIOR. EXTERIOR SHOULD BE MOUNTED AT LEAST
CANARM Ltd. warrants every new fan to be free of defects in material and workmanship, to the extent that, within
a period of one year from the date of purchase CANARM Ltd. shall either repair or replace at CANARM's option,
Moving parts,
disconnect
any unit or part thereof, returned freight prepaid, and found to be defective.
power before
servicing.
This warranty does not include any labour or transportation costs incidental to the removal and reinstallation of
the unit at the user's premises.
WARNING: MOTORS ARE EQUIPPED WITH AUTOMATIC OVERLOAD PROTECTION AND MAY RESTART
Components repaired or replaced are warranted through the remainder of the original warranty period only.
WITHOUT WARNING. ALWAYS DISCONNECT FROM POWER BEFORE ATTEMPTING SERVICE.
This warranty applies to the original purchaser-user only; it is null and void in case of alteration, accident, abuse,
neglect, and operation not in accordance with instructions.
MAINTENANCE
NOTICE: No warranty claims will be honored by CANARM Ltd. unless prior authorization is obtained.
Motor, blade and louvers should be kept clean of any buildup to prevent premature motor failure and to achieve proper performance.
Automatic louvers should be kept operating freely. As with all mechanical equipment scheduled inspections should include checking that
all hardware is secure and blade set screws are tight.
DO NOT PRESSURE WASH THE FAN.
Installation or Product problems? Do not return to store of purchase.
Contact Canarm Service at 1-800-265-1833 (CANADA) 1-800-267-4427 (U.S.A.)
1-800-567-2513 (EN FRANCAIS) Monday to Friday 8:00 - 5:00pm e.s.t.
XFS-M 03/12/14
XFS-M 03/12/14
Instruction Manual
2.5 METERS ABOVE GRADE LEVEL OR PROPERLY GUARDED FROM ACCIDENTAL
CONTACT OF THE BLADE THROUGH THE LOUVERS.
CANARM LTD.
2157 PARKEDALE AVE. PO BOX 367
BROCKVILLE, ONTARIO K6V 5V6
TELEPHONE: (613) 342-5424
FAX: 1-800-263-4598
A X A
MODEL B
SQUARE
XFS10
14 7/8" 8"
XFS12
16 7/8" 8 3/8"
XFS14 18 7/8" 9"
XFS16 20 7/8" 9 1/2"
XFS18
22 7/8" 9 1/2"
XFS20
24 7/8" 9 1/2"
XFS24
28 7/8" 11 1/8"
XFS30
34 7/8" 12 1/2"
WARRANTY
CANARM LTEE.
2555 RUE BERNARD LEFEBVRE
LAVAL, QUEBEC H7C 0A5
TELEPHONE: (450) 665-2535
FAX: (450) 665-0910
N (# OF
C D (c/c) E SQR
LOUVRES)
5" 12 7/8" 11 1/2" 2
5" 14 7/8" 13 1/2" 3
5" 16 7/8" 15 1/2" 3
5" 18 7/8" 17 1/2" 4
5" 20 7/8" 19 1/2" 4
5" 22 7/8" 21 1/2" 5
5" 26 7/8" 25 1/2" 6
5" 32 7/8" 31 1/2" 8
ARTHUR MANUFACTURING FACILITY
#7686 CONCESSION 16, RR4
ARTHUR, ONTARIO N0G 1A0
TELEPHONE: (519) 848-3910
FAX: (519) 848-3948
FRAMING
12" x 12"
14" x 14"
16" x 16"
18" x 18"
20" x 20"
22" x 22"
26" x26"
34" x 34"
Page 1 of 2
Page 2 of 2