Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Jandy
Pro Series Underwater Pool and Spa White Lights | Installation Manual
®
Use only approved wet niches (see following note) to
ensure a safe and proper installation.
NOTE Jandy Pro Series Pool and Spa Lights are
ETL listed (ETL report/file 3101015CHI-
002) for installation with only the following
manufacturer's wet niche fixtures:
Large / Pool Type Niche Model Numbers:
Jandy Pro Series: PLNICLRG, PLNICVFLRG,
Pentair
:620004, 78210200 thru 700,
®
78210401, 79206700
Hayward
DuraNiche: SP0600U
®
Sta-Rite
: 05161-2352 thru 2369, 05163-2395
®
thru 2396
Small / Spa Type Niche Model Numbers:
Jandy Pro Series: PLCNICSM, SSNICSM1(R/S)
Pentair: 78241100, 78242200, 78242300,
78243100 thru 300, 78244100 thru
300, 79206600
Hayward DuraNiche: SP0601U
Sta-Rite: 05166-1017 thru 1034, 05167-1035
thru 1037
3.2
Installing the Light Fixture
NOTE Perform these steps only after the electrical
system requirements are met.
1.
Feed cord through conduit to Junction Box,
leaving at least four (4) feet of cord at the light
fixture to coil around the light; see Figure 1 (or
Figure 2, for spa). This four (4) feet of cord around
the light allows the light to be serviced after the
pool or spa is filled with water.
2.
Cut the cord at the Junction Box, leaving at least
six (6) inches of cord to make connections.
3.
Strip six (6) inches of the outer cord jacket to
expose the three insulated wires. Be careful not to
damage the insulation on the three (3) inner wires.
4.
Install strain relief over cord jacket and connect
all three (3) wires to the corresponding circuit
wires in the Junction Box. Install the Junction Box
cover.
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will get
extremely hot, which may result in serious burns
or in breakage of the lamp or lens. This may result
in serious injury to pool or spa users, installers, or
bystanders or damage to property.
SSNICLRG1(R/S)
ENGLISH
5.
Coil the 4-foot length of cord around the fixture
and place the light assembly into the niche.
6.
Engage the retainer tab on the bottom of the face
ring, then pivot the top of the fixture inward and
tighten the special pilot screw.
WARNING
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically
grounds the mounting ring to the wet niche. Failure
to use the screw provided could create an electrical
hazard, which could result in death or serious injury
to pool or spa users, installers or others due to
electrical shock.
7.
Fill the pool or spa until the underwater light is
completely submerged in water before operating
the light for more than 10 seconds. Turn on
main switch or circuit breaker, and the switch,
which operates the underwater light, to check for
proper operation. Refer to Section 6, Operating
Instructions.
Section 4. Replacing Jandy Pro
Series Light Fixture in an
Existing Pool or Spa
WARNING
Risk of Electrical Shock or Electrocution.
This underwater light must be installed by a
licensed or certified electrician or a qualified pool
or spa serviceman in accordance with the National
Electrical Code in the US, the Canadian Electrical
Code in Canada, and all applicable local codes
and ordinances. Improper installation will create
an electrical hazard, which could result in death
or serious injury to pool or spa users, installers or
others due to electrical shock, and may also cause
damage to property.
Always disconnect the power to the pool or spa
light at the circuit breaker before servicing the light.
Failure to do so could result in death or serious
injury to serviceman, pool or spa users or others due
to electrical shock.
PAGE 7
Publicité
Chapitres
Table des Matières
