Campbell Hausfeld PW2575 Manuel Du Produit page 8

Operating Instructions and Parts Manual
operation (Continued)
Adjusting the high-low nozzle when the
gun is triggered can result in damage to
the seals in the nozzle.
3. After using detergents, flush the
suction system by placing the
detergent suction tube into a bucket
of clean water or rinse out tank.
5. CleaNING PoWer
You can control the cleaning power of
your pressure washer in two ways:
1. Adjust the spray pattern at the
nozzle. Choose the widest pattern
possible for spraying when starting
the job and adjust the pattern to
a narrower angle until you find a
suitable pattern.
2. The easiest way to regulate the
cleaning power of your pressure
washer is by changing the distance
from the surface you are cleaning.
Begin spraying with a wide fan
pattern while standing several feet
from the surface. Slowly move
closer to the object you are cleaning,
adjusting the spray pattern as
necessary, until you find the most
effective cleaning technique.
6. FINal rINSe
The final rinse should start at the
bottom and work upward. Make sure
that you thoroughly rinse the surface
and that you remove all detergent.
7. PreSSure relIeF ProCeDure
To reduce the risk of bodily injury
or property damage, always follow
this procedure whenever spraying is
stopped, when work is completed, and
before checking or repairing any part of
the system.
1. Engage the trigger safety latch.
2. Turn the unit off.
3. Remove the ignition cable from the
spark plug.
4. Shut off the water supply.
5. Disengage the trigger safety latch
and trigger the gun to relieve
pressure.
6. Re-engage the trigger safety latch.
www.chpower.com
7. Before overnight storage, long
term storage, or transporting unit,
disconnect the water supply and
turn off the fuel supply valve.
8. SHutDoWN
1. Be sure all detergent is flushed from
system.
2. Turn the engine OFF.
3 Turn the water supply OFF.
4. After the engine and water supply
are turned off, trigger the gun to
depressurize the system.
neVer turn the
water supply off
before turning the engine/motor off.
serious damage could occur to the
pump and/or engine/motor.
neVer disconnect
the high pressure
discharge hose from the machine
while the system is pressurized. To
depressurize, turn engine/motor off,
turn water supply off and squeeze gun
trigger 2-3 times.
5. After each use, wipe all surfaces of
the pressure washer with a clean,
damp cloth.
• Do not store the pressure washer
outdoors.
• Do not store the pressure washer
where it might freeze unless it has
been properly winterized.
9. StoraGe
loNG terM StoraGe INStruCtIoNS
(More tHaN 30 DayS IN StoraGe)
1. Remove fuel from the tank and run
the pressure washer in a normal
operating mode until the engine
stops from a lack of fuel. Normal
operating mode means actually
spraying water from the gun while
the engine is running.
Alternate method – Add fuel
stabilizer to gas in the tank and run
in normal operating mode for at
least five minutes.
2. Stop the engine, turn off the water
supply, and trigger the gun to
release pressure in the high-pressure
hose.
3. Disconnect the water supply and
high pressure hose from the pump.
4. Allow the engine to cool.
8
5. Disconnect the spark plug wire and
remove the spark plug.
6. Pour 1/2 oz. of engine oil into the
spark plug hole.
never pull the
starter rope on the
engine when the spark plug is removed
unless the spark plug hole is covered.
Fuel vapor from the hole can ignite by a
spark.
7. Place a rag over the spark plug hole
and slowly pull the starter rope
several times to distribute the oil.
WINterIzING INStruCtIoNS
1. Follow and complete the Long Term
Storage Instructions above.
2. Disconnect the spark plug wire.
3. Disconnect the high pressure hose
from the pump.
4. Insert a 12 inch to 14 inch piece of
garden hose into the pump inlet.
5. Place a funnel in the other end of
the garden hose.
read the
manufacturer's
instructions for safe handling and
disposal of rV antifreeze.
6. Pour approximately 6 oz. of RV
antifreeze into the funnel.
7. Pull the starter rope several times
until the RV antifreeze comes out of
the pump outlet.
8. Disconnect the high pressure hose
from the gun and drain the hose.
Hold the gun and lance in a vertical
position and squeeze the trigger to
drain the water out.
tIPS For exteNDING tHe lIFe oF
your PreSSure WaSHer
1. Never operate the unit without
water.
2. Your pressure washer is not meant
to pump hot water. Never connect
your pressure washer to a hot water
supply as it will significantly reduce
the life of the pump.
3. Running the unit for more than
one minute without spraying water
causes heat to build up in the
pump. Running the unit without
spraying water can damage pump
components.