Inoksan BYM042 Mode D'emploi page 9

the lime scale that will accumulate at the internal
surfaces of the boiler and pump will prevent the
device from working efficiently.
3. POWER CONNECTION
 The installation and power connection of the
device must be performed by authorized personnel
according to the standards.
 The device needs to be connected to a network
which is consistent with the DIN VDE 0100
power installment standards.
 Usage of a H07 RN-F quality 3x2,5mm
cable is necessary for the power connector line.
 The device needs to be connected to a master
switch (contact distance 3mm or more) and to a
fused isolator.
 Voltage tolerance ± must not go over % 10.
 A maximum of 25A fuse must be put to the device
feed line.
 We recommend the usage of a 30 mA faulty
residual current device.

The device must absolutely be grounded. For this,
DIN VDE 0100 clause 540 must be taken into
consideration. Grounding screw is indicated at the
bottom right section with the "
4. USER INSTRUCTIONS
 The machine is designed for washing; trays,
plates, glasses, cups, knives and forks etc. dishes
inside specially designed cases for medium scale
businesses and all cafeteria type facilities where
mass catering services are provided.
 The machine must always be operated by
qualified personnel, assigned for this work.
 The machine has the feature of washing maximum
290mm height glasses and other objects.
 Water is an important factor for getting a good
washing result. For this reason, if the hardness of
water passes 12 Fr, we recommend using a "water
softener".
 For a good washing quality, soaking the dishes
before putting them inside the machine is advised.
Otherwise the food residue, lemon peels,
toothpick etc. materials can block the materials
drain pump and alter the washing quality.
 Two types of chemical products are used in the
machine. These are detergent for washing, and
polisher for polishing. The detergent must be an
industrial type (powder or liquid) and foam free.
Apply the determined values by the detergent
manufacturer for the used amount. (Detergent
amount can vary according to the hardness of
water.)
 As standard accessory; there is 1 glass tray in
400x400 mm size in the machine.

Select the relevant tray according to the dishes to
be washed and load them according to the
capacities stated on the chart. Do not start the
machine without entirely filling the tray in order
to save detergent and power.
 Be mindful of the durableness of the dishes that
you will put inside the Dishwashing Machine.
 Never change the location of the machine while it
is operating.
 Be sure that the water input valve is open before
operating the machine.
 Cleaning of the internal parts of the machine
periodically is recommended.
 In order to obtain healthy results in cleaned
2
profile
dishes, the following ground rules must be met.
 Apply the manufacturer's remarks on the
detergent dosage according to the water hardness.
 The wash water must be renewed at least 3 times a
day or when the water loses its ability to clean due
to dirty particles. Washing performed with dirty
wash water causes bad washing results, along with
detergent, polisher and power wastage.
 Do not dry cleaned dishes with a dirty towel.
 Do not place clean dishes on spongy towels or
other materials.
 Use disposable materials or preferably the basket
system.
 Make the constant cleaning of the shelves that you
" tag.
use for storing dishes with special detergents and
disinfectants available in the market.
NOTE: The choice of detergent can be a
determining factor in getting a good wash result,
protection and lifetime of the machine. Therefore
we
contaminating products and not exceeding the
suggested detergent amount.
6.
6.1- Operating
Press the On button to start. Select (low, mid,
high) by pressing the wash program button. Close
the door after inserting the tray inside. Press the
START/PAUSE button. When the program ends,
a
START/PAUSE button in order to stop the
machine between programs. Canceling the wash
can be performed by holding down the
START/PAUSE button.
NOTE: For an ideal washing result, you should
wait until the ready-led is lit, when the boiler
reaches 85°C and the tank reaches 55°C.
 1
 2
paused
 3
 4
temperatures are ready
9
recommend not
USING THE MACHINE
verbal reminder is
ON button (OFF when pressed for 2 sec)
Red when Stand-by, green when operating
START <–> PAUSE (2 sec STOP)
Green when operating, blinks when
Tank Temperature indicator
Red double digit
Ready-led
Will flash red when Boiler and Tank
using abrasive or
played. Press the