Inoksan BYM042 Mode D'emploi page 8

AÇIKLAMA
ER 01
SU YOK Arızası
ER 02
Boiler NTC Arızası
ER 03 Tank NTC Arızası
ER 04
Boiler ISITICI Arızası
ER 05
Tank ISITICI Arızası
Termik Röle ya da
ER 06
Power-box Arızası

Sensör ve Termik hataları düzelince hata kodu kendiliğinden silinir.

Diğer hata kodlarını silmek için ON/OFF tuşuna basınız.
 EXPLANATION
 The instructions in this manual include important
information regarding the secure installation, use,
cleaning and maintenance of the machine.
Therefore, keep this manual in a place where the
user of the machine or the technician can reach
with ease.
 The installation of the machine must be performed
according to the instructions of the producing
company by an expert who is experienced in this
topic.
 The power and water connections of the machine
must be performed in accordance with the given
values in the "Technical Specifications" chart.
 Your machine's proper operation and long life
depends absolutely on correct usage, periodic
maintenance, fulfilling the service operations and
your attention.
 Producer firm does not accept responsibility of;
any operation performed without complying with
the user's manual, maintenance or technical
interventions performed
technicians, eventual damages that harm people or
properties due to extra reservoir or devices.
1. INSTALLATION INSTRUCTIONS
 Carry the device to the place of installation and
remove it from its package.
10 dk. boyunca Tank prosestatı su seviyesi algılamaz, konum
(makine su alma durumundayken 9 nolu girişe 10 dk. boyunca sinyal
Boilerde 10 dk. süre boyunca en az 5 ºC (41°F) ısı artışı
(11 No'lu boiler çıkışının yani K2 kontaktörünün sürekli olarak en az
Tank 15 dk. süre boyunca en az 5 ºC (41°F)ısı artışı sağlanamadığı
(10 No'lu boiler çıkışının yani K3 kontaktörünün sürekli olarak en az
Yıkama pompası termik röle çıkışında enerji olmadığı durumda.
(Elektronik kartın 16 nolu girişine enerji gelmediği durumda)
without authorized
ALGILAMA
değiştirmezse.
ulaşmazsa)
Sensör kısa devre ya da açık devre
Sensör kısa devre ya da açık devre
sağlanamadığı durumda.
10 dk. çalışma durumunda kontrol edilecek.)
durumda.
15 dk. çalışma durumunda kontrol edilecek.)
 Check whether the device is in a solid state. If
there is damage, immediately notify this situation
to your dealer and if you have any doubt do not
operate the device without having it checked by
an expert.
 Peel away the protective nylon on the device. If
there are material remains left on the surface,
clean them with a convenient dissolver. (For
Example;Henkel-Helios)

If possible, place the device near a water
connection and waste water drain.
2. WATER CONNECTION
 Connect your device to the city water normally.
However, you can also connect it to the hot water
input in order to save electricity.
 Perform the connection between the device and
the tap with the provided flexible hose.
 In order for the device to work correctly, the input
water must be at 7 Fr hardness and min 2 bar, max
4 bar pressure.
WARNING:

Drain pipe required to be connected to a
drain at height 50 mm from ground for
base model devices and at max. 700 mm
from the ground for the devices with
pump to maintain a reliable water flow.
 For longer life and efficiency of your device,
attach a lime remover at the water input. Otherwise
8
EN