Conrad N300 Mode D'emploi page 4

Chose your WLAN using "Select" and confi rm using "Connect". In case your WLAN network
is not displayed, click "Refresh".
Be sure to check whether the encryption is set correctly and enter the WLAN password.
Confi rm using "Save".
Wait until the connection is established and the window shows the message "Connect to...
successfully". Then click on "OK".
In case the connection is not established, check the properties and try again.
• The confi guration is now complete. Close the web browser and change the IP address of
your LAN connection back to its original.
After the confi guration
• After successful confi guration, position the repeater in an appropriate place. The best posi-
tion would be centered between your router and the furthermost place where the WLAN
should be available. Note that the repeater has to be in the router's range of coverage.
The device can also be mounted on a wall. Therefore, use the slots on the bottom side.
• When the product is set up and connected to the power supply voltage, you can connect your
computer to the WLAN as usual. The SSID and the WLAN key have not changed.
☞
Please note:
If you want to connect your computer to the WLAN using WPS, only use the WPS
function of your router, not that of the repeater.
• You can also connect the computer to the LAN socket of the repeater using a network cable
(1:1 connected).
If you need more than one network gateway, you can expand it with a network switch.
• No matter how your computer is connected to the repeater, you always get the IP address
from your router, not from the repeater.
☞
If you change the confi guration of your WLAN, you may have to reconnect the re-
peater to the router after the change.
Resetting to Factory Settings
On the back side, on the right, next to the WLAN antenna, a countersunk reset button can be
found, with which the repeater can be reset to the factory settings.
Connect the repeater to the wall power supply and put it into the power supply plug, if this has
not been done already. Wait about 20 seconds until the self test has fi nished. Hold the reset
button for about 10 seconds until the power LED starts blinking. Let go of the button.
The repeater restarts; this takes about 20 seconds. Then the repeater is reset to the factory
settings (IP address 192.168.2.250; username "admin" and password "password").
Handling
• Any maintenance or repair work may only be performed by an authorised repair shop.
• Check the product for damage before each use!
If you detect any damage, DO NOT connect or use the product! This may present
a danger to life!
• A safe operation can no longer be assumed, if:
- the product shows visible signs of damage,
- the product does not function or does not function properly (e.g., if it produces a
smell of burning)
- the product was stored under unfavourable conditions
• When setting up the product, make sure that the cables are neither kinked nor
pinched.
Maintenance and Cleaning
The product does not require any maintenance and should never be disassembled for any
reason.
Disconnect the product from the power supply before cleaning, unplug the wall plug trans-
former from the mains socket (all network connections will cease to function). Also disconnect
the RJ45 cable.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Do not use aggressive cleaning agents as these can cause discolouration.
Do not press too strongly on the surface, to prevent scratch marks.
Disposal
Electrical and electronic products do not belong in household waste!!
Please dispose of an unserviceable product according to the current statutory re-
quirements.
Technical Data
a) Repeater
Operating voltage .........................12 V/DC
Network adapter ...........................RJ45, 10/100MBit
WLAN ...........................................802.11b/g/n (max. 300MBit)
b) Wall plug transformer
Operating voltage .........................100-240 V/AC, 50/60 Hz, 0,3 A
Output ...........................................12 V/DC, 1 A
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EC.
☞
The Declaration of Conformity (DOC) for this product can be found at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.