Télécharger Imprimer la page

CYBEX gold PALLAS G I-SIZE Mode D'emploi page 11

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
SWITCH FROM IMPACT SHIELD (76 CM – 105 CM) TO THE VEHICLE
BELT (100 CM – 150 CM)
Remove the Impact Shield (g) as soon as your child is taller than 105 cm or
weighs more than 21 kg.
Open both Buckles of the Impact Shield (h) and remove the Impact Shield (g).
Note that using the seat without an impact shield is not permitted before
��
your child reaches a height of ≥ 100 cm.
��
Keep the impact shield in a safe and secure place.
SECURING THE CHILD WITHOUT IMPACT SHIELD: 100 CM – 150 CM
1. Route the vehicle seat belt around your child and insert the belt tongue into
the belt buckle. It must lock into place with an audible "CLICK".
2. Place the lap belt in the green coloured Lap Belt Guides (m) of the car seat.
3. Pull the shoulder belt to tighten the lap belt.
4. On the side of the car seat next to the belt buckle, the shoulder belt and the
lap belt must be inserted together in the Lap Belt Guide (m).
5. Feed the shoulder belt through the green Shoulder Belt Guide (e) until it is
inside the belt guide.
6. Ensure that the shoulder belt runs across your child's clavicle and does not
touch your child's neck. If necessary, adjust the height of the Adjustable
Headrest (b) to change the position of the belt.
ADJUSTING THE LYING POSITION
1. To put the seat in the lying position, press the Position Adjustment Button
(w) on the underside of the front area of the booster (c).
2. To return the seat from the lying position to the sitting position, press the
Position Adjustment Button (w) again and guide the seat upwards with light
pressure against the booster (c).
LINEAR SIDE-IMPACT PROTECTION (L.S.P.)
If the Linear Side­impact Protection (f) is in conflict with the car door or if it
affects the amount of space left on the passenger seat, it is possible to detach
it. To do so, press the Side Impact Proctection Release Button (v). To reach
this button, the cover of the backrest needs to be removed. To reattach the
L.S.P. (f) to the seat, follow the removal instructions in the reverse order.
RECLINING HEADREST
The Reclining Headrest (y) helps to prevent the child's head from dangerously
tipping forward during sleep.
It can be set to one of three positions.
Push the Reclining Headrest (y) forward until the desired position is reached.
��
The child's head should always be in contact with the Reclining Headrest.
REMOVING AND REATTACHING THE SEAT COVER
The cover of the car seat consists of four parts (headrest, backrest, booster
and impact shield). These are held in position at several places by press studs
and elastic bands. Once all attachments have been released, the single parts
of the cover can be removed.
In order to put the covers back on the seat, follow the removal instructions in
the reverse order.
The cover may only be washed at 30 °C with a delicate wash program
��
otherwise it may result in discoloration of the cover fabric. Please wash
the cover separately from other laundry and do not dry in the dryer or in
direct sunlight!
WARRANTY AND DISPOSAL REGULATIONS
CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you
3 years warranty on this product. The warranty is valid in the country, where
this product was initially sold by a retailer to a customer. The contents of
the guarantee and all essential information required for the assertion of the
guarantee can be found on our homepage www.cybex-online.com. If a
warranty is shown in the article description, your legal rights against us for
defects remain unaffected.
Please observe the waste disposal regulations in your country.
EN
9

Publicité

loading

Produits Connexes pour CYBEX gold PALLAS G I-SIZE