Publicité
EN - IMPORTANT
The features of this product are of the utmost importance for the safety of people.
It is not permitted to carry out any modifications to the product, and no assembly other than the one described herein is allowed.
1 – Field of application
The field of application of this panic bolt is limited as follows:
Maximum mass
Maximum height
of the door
200 Kg
The effective width of the activation bar X, shall be as close as possible to the door opening Y, yet not less than 60% of it. This panic bolt cannot be
fitted on swing doors. The panic bolt must be assembled in a way as to keep the bar between 900 and 1100 mm from the floor. If most users are
children, consider the possibility to reduce the height of the bar.
2 – Recommendations for the correct installation and assembly
- The panic bolt is manufactured in conformity to the EN 1125:2008 standards. High safety degree for both people and things is ensured if it is installed
on doors and frames in good conditions.
- Make sure that the door has been properly installed and that there is no hindrance to its movement.
- Make sure that the seals fitted on the complete doors do not affect the correct working of the panic bolt.
- Prior to assembling the panic bolt on a fire/stop door, check the fire resistance certification to make sure that the panic bolt is suitable for use on that
particular door.
- In case of double doors, when a panic bolt is installed on both wings, make sure that each wing opens when the panic bolt is operated and that both
wings open freely when the two panic bolts are operated simultaneously.
- Follow the assembly instructions scrupulously during installation. The maintenance and assembly instructions must be delivered to the user by the
installer.
- Locking elements and vents must be installed in such a way as to safely engage to each other. Make sure that the projection of the locking elements,
when they are in the retracted position, do not affect the free rotation of the door.
- In case of panic bolt assembly on double doors with automatic locking devices, a locking sequence coordinator must be installed to ensure that the
locking sequence is carried out in the right way.
- The device is not suitable for installation on doors with slip-in applications.
- Application on glazed doors is possible, provided the glass is of laminated / tempered type.
- No device allowing the door to be locked in the closing position shall be used, except those reported in this European Standard. This does not
prevent automatic safety locking devices from being installed.
- A notice "press bar to open" or a drawing (see the side picture) must be placed on the internal side of the door, over the operating bar or
on the bar itself if possible.
- The device has been tested to fire resistance: minimum resistance is 90 minutes.
- The fastening system complies with the standard requirements of § 4.3 EN 1125:2008 (see test report SRP01713).
- If a door locking device must be used to bring the door back in its closed position, make sure to guarantee an easy exit to children, old and invalid
people.
- All vents or protection plates, if supplied, must be fitted to ensure the compliance with the EN 1125:2008 standard.
- Certification decays if the device: - has been damaged; - has been exposed to fire which may have altered its ascertained properties; - no longer
corresponds to the registered documentation (e.g. modifications or alterations by third parties).
- FAPIM spa is responsible solely and exclusively if the panic device installed is made up of Fapim OLTRE components only.
3 – Recommendations for maintenance
Users or their authorized representatives are recommended to carry out the following maintenance checks at least twice a year; installer and/or user,
with respect to the prescriptions mentioned in art. 4 of the Ministerial Decree of 03/11/2004 for fire safety, are requested to register the operations
carried out in the following table:
A) Check and operate the panic bolt and make sure that all the components are i good working conditions. Make sure that the fixing screws are
securely tightened.
B) Check that the vent or vents are free from obstructions.
C) Check that the contact surfaces of the latch bolts and of the vents are well lubricated. If necessary, lubricate with Tecnolube Seal SYNTHY HTL
GREASE 5500 grease type or other equivalent having an operating temperature and viscosity suitable for the conditions of use.
D) Check that no locking devices have been installed in addition the original configuration;
E) Check periodically that all system components are still those specified in the list of components initially supplied;
F) Check periodically that the operating element is correctly secured and, by means of a measuring device, verify the strength required to open the
door. Check that the operating force has not considerably changed with respect to the first installation.
You can download the Declaration of Performance – DoP – from the webpage www.fapim.it in the appropriate "Product Certification" section.
You can download the register of installation and maintenance of the panic device in the "Catalogue" section of the website www.fapim.it seeking the
item codes of the central locks.
Maximum lenght
of the door
of the door
2.520 mm
1.320 mm
X
Y
Minimum and maximum
working temperatures
- 10° C / +60°C
1320 mm
3/8
Life in evolution
Publicité
