Operating And Safety Instructions - Unitec 77084 Mode D'emploi

77084 Bed.:Lay 01.03.2011
GB

Operating and safety instructions

These LED vehicle daylight / marker lights from UNITEC have been carefully designed and manu-
factured to ensure all-round reliability. Before using your LED vehicle daylight / marker light,
please read carefully through these instructions, which contain all you need to know in order to
ensure that your LED vehicle daylight/marker lights give you many years of reliable service.
Please keep the instructions in a safe place for future reference.
Please observe the permitted installation-width and height
limits (see plan). The two LED lamps must be fitted at least
600 mm apart from one another. Be sure to observe the
maximum distance of 400 mm between the side of the
LED lamp and the outer edge of the vehicle's wing. The
minimum distance between the LED lamp and the roadway
is 250 mm. The maximum installation height with respect to
the roadway is 1500 mm. Both lamps must be at the same
distance from the roadway and their respective sides of
the vehicle.
In order to prevent short circuits and possible injuries, stop the engine and switch off the
ignition before carrying out electrical work of any kind. If you are in any doubt as to your level of
knowledge or skill, please contact a specialist installation workshop.
Suitable for 12V DC and 24V
power capacity approx. 6 watts
LED vehicle daylight / marker lights offer the extra
safety that comes with increased visibility in traffic.
Disconnect the wires (coloured white and black
respectively) from the battery-box wires before
installing the LED vehicle daylight / marker lights.
These are used to carry out the test function.
Once you have installed your LED vehicle
daylight/marker lights in their corresponding posi-
tions on the vehicle, following the instructions
shown in fig. 1, you can connect them to the on-
board electronic system. Please refer to the circuit diagram shown above (fig. 2) when doing so.
1. Connect the yellow wire to both lights and one wire to the + (plus) pole lead of the existing
sidelight.
2. Connect both LED vehicle daylight / marker lights to the black wire, and also to a wire leading
from the - (negative) pole of the vehicle's battery, or to a suitable earthing (ground) point on
the body.
3. To conclude the operation, connect the white lead to the lights and to the + (plus) terminal of
your vehicle's ignition system.
4. Permanently deactivate your vehicle's standard front parking lights/marker lights.
In principle the installation of the LED vehicle daylight/marker light may cause faults or error
messages in the onboard monitoring system (onboard computer). In this event contact a specia-
list garage. It may be able to rectify or eliminate the fault. You can also read or delete this fault
with an "OBD II scanner".
Once installation is complete, the LED vehicle daylight/marker light should work when the engine
is switched on. Then please also check that the LED vehicle daylight light switches to the marker
light mode when the normal headlights are switched on i.e. the brilliance of the LEDs will be
somewhat reduced.
In new vehicles, including Audi and VW from build year 2006, the current strength going to the
lamps was somewhat reduced into order to prolong the service life of the lights. In consequence,
it may be that the LED lights do not correctly switch to position light (dimming) when the conven-
tional headlights are switched on. In order to continue using the function, you should install a
conventional 12 V / 10 A relay as shown in fig. 3; this relay is not included in the scope of delivery.
Fig. 3
positive wire of parking light
(left side)
ground
Do not dispose of this product in the domestic waste at the end of its useful life. You can find out
more details from your official disposal body. Do not dispose of the battery in the domestic waste
but take it to the special waste disposal point.
14:26 Uhr
DC systems. LED
Fig. 2
yellow wire yellow wire
lamp
(left side)
black wire black wire
white wire white wire
Seite 3
Fig. 1
yellow wire
black wire white wire
positive wire of parking light
(right side)
ground
lamp
(right side)
The cables are not included
in the scope of deliverie
Welcome
Note on safety
Technical specifications
Function
Fitting instructions
Attention:
Disposal instructions