DWT EX03-125 D Notice Originale page 21

• Put the polishing accessory on the sanding plate 6�
Follow the rules below:
• the polishing layer should be on top (adhesive
surface of sanding plate 6 must be attached to the
adhesive surface of the polishing accessory);
• the brims of polishing accessory and sanding
plate 6 must match�
• Firmly press the polishing accessory against the
surface of sanding plate 6�
Attention: when pressing the sheet,
ensure that the polishing accessory
remains properly placed on sanding
plate 6.
Using the dust bag
During work, always use dust bag 8�
One should monitor dust level in dust bag 8 and empty
the bag at relevant time, taking the aforesaid precau-
tions�
Mounting / dismounting of the dust bag (see
fig. 5)
• To mount, insert the connecting pipe of dust bag 8
into the dust removal port 5 (see fig. 5).
• To dismount, pull out the connecting pipe of dust
bag 8 from dust removal port 5�
Emptying the dust bag (see fig. 6)
• Disconnect the power tool and remove dust bag 8 in
the manner described above�
• Remove textile bag 14 from the plastic body 13 (see
fig. 6).
• Taking the precautions described above, empty the
content of textile bag 14 by shaking, for better results,
turn the bag inside out and use a soft brush to clean it�
When washing textile dust bag 14, use it only after
the bag has dried completely.
• Put textile dust bag 14 on plastic body 13�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
tool on / off
[EX03-125 D, EX03-150 D]
Switching on:
Move forward on / off switch 4�
Switching off:
Move backward on / off switch 4�
[EX03-125 DV]
Short-term switching on / off
To switch on, press and hold on / off switch 4, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch 4 and lock it in the position with
lock-on button 10�
Switching off:
Push and release on / off switch 10�
the power tool operation
Dust collection decreases dust concentra-
tion in the air and prevents build up of dust at
the work station�
Use of vacuum cleaner
During prolonged wood machining or when processing
materials that produce dusts hazardous to health, the
power tool should be connected to a proper vacuum
cleaner�
Given power tools may cooperate with the vacuum
cleaner only when used with a relevant connector�
One should monitor dust level in the bag and empty the
bag at relevant time, taking the aforesaid precautions�
Oscillation rate regulator
[EX03-125 DV]
The oscillation rate regulator 9 is purported to set the
desired oscillation rate of sanding plate 6�
• Push on / off switch 4 and lock it in the position with
lock-on button 10�
• Set the desired oscillation rate�
The required oscillation rate depends on the type of
processed material, work conditions and must be set
on the basis of practical trials for best results�
During prolonged work at low oscillation rate, one
should allow the power tool to cool down for 3 minutes�
For this purpose, set the maximum oscillation rate and
allow the power tool to work without load�
on the power tool operation
Sanding sheet selection
Prior to commencement of work, select the sanding
sheet 7 type that is most suitable for the processed
material or surface� The type of sanding sheet 7 is
specified on the package. One may also ask the ven-
dor for more information�
Various works require the use of sanding sheet 7 of
different coarseness, allowing a surface of required
smoothness to be obtained� The best method to select
sanding sheet, is to practically test for best results�
Sanding
Prior to commencement of work one
should perform test sanding on an un-
necessary element (made of the same
material or with the same coating as the
English
21
Dust suction during
Design features
of the power tool
Recommendations