BEGLEC JB SYSTEMS SPACE-1 Mode D'emploi page 6

ENGLISH
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
• Press the MENU button until
is shown on the display.
• Press the ENTER button, the display starts blinking.
• Use DOWN and UP button to select
• Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for
the DMX-signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to
standalone mode.
• Press the MENU button until
is shown on the display.
• Press the ENTER button, the display starts blinking.
• Use DOWN and UP button to select
• Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.
• Press the MENU button until the display shows
• Press the ENTER button, the display starts blinking.
• Use DOWN and UP buttons to select
when not used).
• Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
• Press the MENU button untill
is blinking on the display. (normal display)
• Use the ENTER button to change to the mode
be automatically stored after 8 seconds. Or press the ENTER button again return to the
mode (normal display).
• To go back to the functions press the MENU button.
Self-Test
Used to activate the internal "self-test" program which shows all possibilities of the unit.
• Press the MENU button untill
is blinking on the display.
• Press the ENTER button to start the internal self-test program.
• To go back to the functions press the MENU button.
JB SYSTEMS®
OPERATION MANUAL
(normal) or (2 light show) mode.
(yes blackout) or (no blackout) mode.
.
(display always on) or (display off
(display inversion), the option will
7/60 SPACE-1 Laser
ENGLISH
Fixture Hours
Used to show the number of working hours of the unit.
• Press the MENU button untill
is blinking on the display.
• Press the ENTER button to show the number of working hours in the display.
• To go back to the functions press the MENU button.
Reset
Used to force a reset of the unit.
• Press the MENU button untill
is blinking on the display.
• Press the ENTER to reset all channels to their standard position.
• To go back to the functions press the MENU button.
CONTROLLING THE LASER
• Regular breaks during operation are essential to maximize the life of this device as it is
not designed for continual use.
• Do not switch the unit on and off in short time intervals as this reduces the lamp life.
• Always unplug the unit when it is not used for a longer time. or before replacing the bulb
or start servicing.
• In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
• Important: Never look directly into the laser beam! Don't use the effect in the presence
of persons suffering from epilepsy.
Every time you turn the unit on, it shows "ILSS" on the display and move all the motors to
their 'home' position and you may hear some noises for about 20 seconds. After that the
unit will be ready to receive DMX signal or run the built-in programs.
You can operate the unit in 5 ways:
• Standalone 1unit
• By master/slave built-in preprogram function
• By CA-8 easy controller
• By universal DMX controller
• By iLEAD Controller
1. Standalone 1unit:
Important! This mode only works when the blackout mode in the menu is set to
OFF, otherwise nothing will happen! Read more about this option in the "Main
Menu" paragraph.
Just connect the unit to the mains and put on some music. The unit will start working
automatically to the rhythm of the music.
2. By master/slave built-in preprogram function:
Important! This mode only works when the blackout mode in the menu of the
master is set to OFF, otherwise nothing will happen! Read more about this
option in the "Main Menu" paragraph.
JB SYSTEMS®
OPERATION MANUAL
8/60 SPACE-1 Laser