Sunex Tools SXC610 Instructions D'utilisation page 4

Operating Instructions •
Nipple
Air Supply...
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI at the
tool while running free. Higher pressure (over 90 psig; 6.2 bar) raises
performance beyond the rated capacity of the tool, which will shorten
tool life because of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in
the air line will cause damage to the tool. Drain the air tank daily.
Clean the air inlet filter screen on at least a weekly schedule. The
recommended hookup procedure can be viewed in the above figure.
The air inlet used for connecting air supply, has standard 1/4" NPT.
Line pressure should be increased to compensate for unusually long
air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D.
and fittings should have the same inside dimensions and be tightly
secured.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no air line oiler
is used, run a teaspoon of oil through the tool. The oil can be squirted
into the tool air inlet or into the hose at the nearest connection to the air
supply, then run the tool.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS ®
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will replace any SXC Series Air Tool which fails to give satisfactory service due to defective workmanship
or materials. This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will replace free of charge
any part or unit which proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover
any repairs or replacement made by anyone other than Sunex Tools or its authorized warranty service centers.The foregoing
obligation is Sunex Tools' sole liability under this or any implied warranty and under no circumstances shall we be liable for any
incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. Return tool to Sunex Tools, transportation prepaid. Be
certain to include your name and address, evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state. After the one year direct replacement warranty has expired, some
service parts are available for purchase through normal Sunex Tools service options.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SXC610
Warning Information • Parts Breakdown
Operation...
• Always use the recommended wheel guard to prevent injury
from broken grinding wheel parts. If a guard has withstood a
• Always wear impact-resistant eye and face protection when
involved in the operation of this tool. Even small projectiles can
the air grinder speed.
• Before grinding, test grinding wheel by briefly running the tool
at full throttle. Be sure to use a barrier (such as under a heavy
work table) to stop any possible broken wheel parts.
To Assemble Grinding Discs:
1. Use stop spanner (#39) to hold gear shaft (#33).
2. Screw on disc nut (#37) with shoulder side facing tool.
Tighten.
3. Attach grinding disc wheel.
4. Screw on other disc nut, (#37) shoulder side facing tool.
Secure tightly with disk spanner (#40)!
4
wheel breakage, discontinue its use and replace
it with a new guard. It may be damaged. Position
the guard between the grinding wheel and the
operator. Use barriers to protect others from wheel
fragments and grinding sparks.
injure eyes and cause blindness. A grinding
wheel that bursts can cause very serious injury.
Daily measure the air grinder speed with a
tachometer to make sure it's not greater than
the RPM marked on the grinding wheel. Never use
a grinding wheel marked with a speed lower than
Rev. 01/11/05