Publicité
Les langues disponibles
Les langues disponibles
Installation Instructions - Junction Box Structure Interface (Connection at Ceiling) - Single Swivel Pendant
Pipe Mounting - SS_ST
WARNING
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION
INSTRUCTIONS.
Before starting any work ensure that all sources of power are turned OFF . All work must meet local/national electrical
●
●
codes and be performed by a certified electrician.
Follow product label information and instructions before installing fixture. Retain installation instructions for future
●
●
reference.
Risk of fire, electrical shock, cuts and or other casualty hazards. This product must be installed in accordance with the
●
●
applicable installation code by a person familiar with the construction and operation of the product and the hazards
involved. Eaton's cooper lighting business assumes no responsibility for claims brought about by improper or careless
installation or handling of this product.
Risk of burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.
●
●
Replace lamp only with correct wattage and type of lamp marked on label. DO NOT exceed the maximum wattage listed
●
●
on the fixture label.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.
●
●
If supply wires are located within 3 inches of driver/ballast, use wire rated for at least 90°C (194°F).
N
otee:
Not all option available. Please consult your Cooper Lighting representative for availability. Specification and
dimension subject to change without notice.
Installation Instructions - Junction Box Structure Interface (Connection at Ceiling) - Single Swivel Pendant Pipe Mounting - SS_ST
ADE141894
2
NOTICE
www.eaton.com
Installation Instructions - Junction Box Structure Interface (Connection at Ceiling) - Single Swivel Pendant
INSTALLATION
Mount Details
4" Octagonal Box
W/ Cross Support
(By Others)
Pendant Wire
(By Others)
3/8" Pendant
5" Canopy
1/4 IPS Nut
Figure 1.
Power
Connection at Ceiling
1.
Layout mounting locations. (Figure 1.)
2.
Ensure that power feed is at the UL end of the fixture.
Power Feed: To be installed to local/national
electrical codes by a certified electrician.
3.
Secure junction boxes to structure.
4.
Secure cross bar to junction box.
5.
Attach pendant to swivel ball and secure using 1/4" IPS
lock nut.
6.
Feed wires through pendant to allow access in junction
box and connect wires ensuring all connections are
properly matched.
7 .
Slide canopy up pendant and attach to swivel crossbar.
N
otee:
Nominal ID for 1/4 IPS = 9.5 mm, 0.375 In.
Power wires can run through any pendant (refer to
N
otee:
local/national electrical codes).
N
otee:
Contact Corelite for connecting power at a joint for
Navigator II.
Installation Instructions - Junction Box Structure Interface (Connection at Ceiling) - Single Swivel Pendant Pipe Mounting - SS_ST
ADE141894
Pipe Mounting - SS_ST
Threaded
Structure
Swivel Ball
Swivel
Crossbar
Figure 2.
Non-Power
Appropriate
Hardware to
Structure (By Others)
Figure 3.
Power (2-D)
Figure 4.
Non-Power (2-D)
Mounts Locations
Distances are Equal to Fixture Length Plus or
Minus Dimensions Below
Fixture Family
DIM "A"
DIM "B"
DIM "C"
DIM "D"
Class A
- 1 1/8"
- 1 1/8"
0"
0"
Iridum
- 1 1/8"
- 1 1/8"
0"
0"
Stellar
- 2 3/8"
- 2 3/8"
0"
0"
RZL
- 2 3/8"
- 2 3/8"
0"
0"
Minigator
- 1 1/8"
- 1 1/8"
0"
0"
Navigator II
+ 5/8"
- 5/16"
0"
+ 15/16"
www.eaton.com
3
Publicité
