Publicité
Les langues disponibles
Les langues disponibles
4.2 - Add a configured spot in the USER file :
For a spot to be configured, it is possible to configure:
The pre-tightening stage
The pre-heating stage
The different pulses (4 pulses maximum)
And the hot and cold forging stage.
To change the settings, click on the buttons
When the operator changes a parameter, the spot chronogram is updated.
To validate the spot configuration, click on the button
To cancel the spot configuration, click on the button
4.3 - Modify a spot configured in the USER file:
To change the settings of a spot, select a spot from the list and then change the welding settings.
To validate the changes, click on the button
To cancel the changes, click on the button
4.4 - Delete a configured point in the USER file:
Select a spot parameter from the list and click on the button
JBDC
Raison sociale :
ZI, 134 Bd des Loges
Adresse :
53941
Code postal :
Saint-Berthevin
Ville :
OPERATEUR
Intervenant :
977AC92
Ordre de réparation :
05/04/2018
Date du journal :
AILE ARRIERE
Intervention :
Commentaires
Commentaires :
1712009013)
Id
Date
Mode
Outil
Temps
(ms)
1
05/04/18 10:22
Auto
Pince en C n°1
630
2
05/04/18 10:22
Auto
Pince en C n°1
630
3
05/04/18 10:22
Auto
Pince en C n°1
490
4
05/04/18 10:22
Auto
Pince en C n°1
510
5
05/04/18 10:22
Auto
Pince en C n°1
510
6
05/04/18 10:23
Normal
Pince en C n°1
350
7
05/04/18 10:23
Normal
Pince en C n°1
350
8
05/04/18 10:23
Normal
Pince en C n°1
400
9
05/04/18 10:23
Normal
Pince en C n°1
400
10
05/04/18 10:23
Normal
Pince en C n°1
400
11
05/04/18 10:23
Manuel
Pince en C n°1
400
MI300I 220V
Then double-click in the second column to select a manufacturer file previously downloaded from our
website.
The list of spots set by the manufacturer is displayed in the second list. Select a configured point to
view the chronogram and configured parameters.
To add a spot to the USER file, select the USER file from the file list and click on the button
right of the list of configured spots. Enter the name of the spot and press the TAB key or click outside
the list of configured spots to configure the welding parameters.
.
.
.
.
.
0243510101
Téléphone :
0243510102
Télécopie :
contact@companyname.com
Email :
www.companyname.com
Site Web :
PEUGEOT
Marque :
308SW
Modèle :
12365849
N° châssis :
1450UT53
Immatriculation :
01/01/2017
Mise en circulation :
Consignes
Mesures
Serrage
Serrage
Epaisseur
Intensité (kA)
Intensité (kA)
(daN)
(daN)
(mm)
9,4
325
9,4
325
3,5
9,4
325
9,3
325
3,5
8,2
240
8,2
240
2,0
8,3
250
8,2
245
2,1
8,3
250
8,3
245
2,1
-
7,3
225
7,3
225
-
7,3
225
7,2
225
-
8,1
265
8,0
265
8,1
265
8,1
260
-
-
8,1
265
8,1
270
-
8,1
510
8,1
440
to the right of the list.
Etat
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Point Ok
Pression faible
EN
to the
31
Publicité
