Limited Warranty- Nordik - Thermo Concepts NORDiK Manuel D'instructions

LIMITED WARRANTY - NORDIK
First year:
During the 1st year after the original
Concepts shall replace or repair (manufacturer's option) any part or
function of the cooler that proves to be inoperative or defective due
to a defect in material or workmanship. Labor costs are the respon-
sibility of the Manufacturer. The original sales slip (invoice) with the
corresponding serial number must support the claim.
Second year through third year:
Within the second through third year, Thermo Concepts will replace
or repair (manufacturer's option) the sealed refrigeration cycle in
case of defect in material or workmanship. The Manufacturer will
provide the parts and labor, through its approved service center or
the factory repair department. The sealed refrigeration cycle does
not include the electrical parts such as the relay, the overload, the
cold-water thermostat, the switch, the hot water thermostat and the
hot overload.
In addition to the sealed refrigeration system, if parts such as hot
water thermostat, compressor relay, overload, cold water thermo-
stat, internal wiring, cord set, become inoperative due to a defect in
material or workmanship, the Manufacturer will replace them
through an approved service center or the factory repair center. The
labor cost to change any of these parts in this paragraph will be the
responsibility of the end user (owner).
Transportation or any other type of compensation is not included.
General provisions and exclusions:
Warranty will be void unless work is performed by an approved service center or the facto-
ry service center.
The original sales slip with the corresponding serial number must support every claim.
Warranty is valid for original purchaser (user) only and may not be transferred.
The warranty does not cover performance, failure or damages of any part resulting from
external causes such as alterations, misuse or abuse, misapplication, corrosion or acts of
God.
This warranty does not apply if the affixed serial number is removed, defaced or obliterated.
The warranty is limited to the value of the cooler and it does not cover performance, failure
or damages resulting from its utilization.
purchase date, Thermo
36
LIMITED WARRANTY - PACIFIK ET BALTIK
First year:
During the 1st year after the original
shall replace or repair (manufacturer's option) any part or function of
the cooler that proves to be inoperative or defective due to a defect in
material or workmanship. Labor costs are the responsibility of the
Manufacturer. The original sales slip (invoice) with the corresponding
serial number must support the claim.
Second year through fifth year:
Within the second through fifth year, Thermo Concepts will replace or
repair (manufacturer's option) the sealed refrigeration cycle in case of
defect in material or workmanship. The Manufacturer will provide the
parts and labor, through its approved service center or the factory repair
department. The sealed refrigeration cycle does not include the electri-
cal parts such as the relay, the overload, the cold-water thermostat, the
switch, the hot water thermostat and the hot overload.
In addition to the sealed refrigeration system, if parts such as hot water
thermostat, compressor relay, overload, cold water thermostat, internal
wiring, cord set, become inoperative due to a defect in material or work-
manship, the Manufacturer will replace them through an approved
service center or the factory repair center. The labor cost to change any
of these parts in this paragraph will be the responsibility of the end user
(owner).
Transportation or any other type of compensation is not included.
This warranty does not apply to any water components that become inoperative due to lim-
ing conditions.
Only original parts can be used and they are covered by the warranty.
Shipping and handling fees shall be borne by the customer and any shipment must be done
with adequate packaging to avoid warranty cancellation.
The foregoing is in lieu of all other agreements expressed, implied or statutory and all other
obligations of liabilities of the Manufacturer. The Manufacturer does not assume or author-
ize any person to assume any obligations of liability in connection with this product. Under no
circumstance will the Manufacturer be liable for any special or consequential damages or
for any delay in the performance of this agreement due to causes beyond his control.
This warranty applies only within the limits of Canada and the United States. However, a num-
ber of foreign distributors benefit from an official certification from the Manufacturer, which
covers this warranty. Please contact your local distributor for further details.
purchase date, Thermo Concepts
37