glass 1989 NOOR STEAM PANEL Notice D'installation, Utilisation & Maintenance page 12

INTRODUCTION
This manual is designed to be used b installers. It describes
the s stems and methods to be adopted for a correct installation
of the product.
The product is not dangerous for the end user if installed, used
and maintained in accordance with the instructions provided
b the manufacturer and on condition that the electrical and
mechanical parts are kept in perfect working order.
For this reason the instructions provided in this manual must be
meticulousl followed.
The supporting structure is highl resistant.
The product is built to conform to standard low -voltage
directives 2006/95/EEC.
The protection class is IPX4 and the rated voltage is 230V;
2700~3500 W for the steam bath version.
Compliance with the level of safet laid down b European
electromagnetic compatibilit
guaranteed b implementing the following European standards
on the product:
EN 55014-1
EN 55014-2
SYMBOLS USED
IN THIS MANUAL
s mbols described below are used in this installation manual
and on certain parts of the product itself.
CONVENTIONAL SYMBOLS AND THEIR MEANING.
WARNING
DANGER OF ELECTROCUTION.
Warn user that, if the described operation is not performed
observing safet regulations, there is a risk of electric shock.
WARNING:
GENERAL DANGER.
Warn user that, if the described operation is not performed
observing safet regulations, there is a risk of ph sical injur .
WARNING:
HOT SURFACE.
Do not touch the steam dispenser during the steam bath! Hot
surface, drops of water can form.
NOTE.
Inform the personnel involved - information that, if not observed,
ma lead to minor injuries to people or damage to the product.
WARNINGS.
Inform the personnel involved -important information.
HYDRAULIC INSTALLER.
skilled technician capable to install the product under normal
conditions and carr out all adjustments, maintenance and
repair jobs on mechanical parts as necessar . The technician is
not authorised to work on live electrical s stems.
ELECTRICAL INSTALLER.
Specialist technician capable of installing the product under
normal conditions, is responsible for all electrical work, such as
ENGLISH
directives 2004/108/EEC is
setting, maintenance and repairs. The technician is capable of
working in energized control cabinets or on electrical sockets.
WARNING
Inform features present onl in some versions of the products.
OPTIONAL
Items present onl if ordered.
CONSUMPTION MATERIAL
Items not provided b the manufacturer.
SAFETY REGULATIONS
efore installing the product, check that the oor where it
will be installed is suf cientl levelled, that it can support its
weight (see installation preparations) and that all necessar
inlets and outlets have been provided.
ou must also make sure that the walls and/or oor, on which
the product will be placed up against/installed, are full tiled
for the entire extension of the product.
Product maintenance and setup must be performed exclusivel
b specialised service personnel onl .
emember that all inspection and protective panels must be
re tted after maintenance or adjustment.
Due to its weight and size, the appliance must be assembled
installed b more than one person.
Do not tamper,disable or disconnect the product devices.
In an case, do not create b -passes or use them for purposes
other than those for which the were installed.
Do not remove or tamper with the inspection panels and do
not remove or conceal the product identi cation labels.
Installation of electrical devices (sockets, switches, lamps,
etc.) inside the bathroom where the appliance is to be installed
must be in compliance with current regulations.
It is absolutel forbidden to use an t pe of electrical appliance
inside or next to the product during use.
The product connection point to the electrical s stem must
be protected against an contact with the steam generator,
which can reach high temperatures, close to 100° C.
WARNING.
Do not use acetic silicone.
ead the instructions supplied with the bottle to make sure
that the silicone is not acetic.
If acetic silicone is used, acr lic parts might be damaged.
If ou need to replace an parts, contact our nearest service
centre and use original spare parts onl .
t the end of the product's life, do not abandon it in the
environment; contact a disposal rm.
WARNING.
The manufacturer declines all responsibilit :
If the installation and maintenance instructions contained
herein are not complied with.
If the product is not used or installed in compliance with the
existing standards of the installed countr .
If the special maintenance is not carried out b quali ed
personnel.
12