Dexter 500HD2.5 Mentions Légales & Consignes De Sécurité page 193

6. OPERATION
Start
Start the tool by squeezing the variable speed trigger switch.
Start the tool by squeezing the variable speed trigger switch.
Start the tool by squeezing the variable speed trigger switch.
Release the trigger to stop the tool.
Release the trigger to stop the tool.
Start the tool by squeezing the variable speed trigger switch.
Release the trigger to stop the tool.
If you press the lock-on button while the trigger switch is depressed, the switch is kept in the operating position. This is convenient when continuous
If you press the lock-on button while the trigger switch is depressed, the switch is kept in the operating position. This is convenient when continuous
Release the trigger to stop the tool.
If you press the lock-on button while the trigger switch is depressed, the switch is kept in the operating position. This is convenient when continuous
operating for extended periods of time is required.
operating for extended periods of time is required.
operating for extended periods of time is required.
If you press the lock-on button while the trigger switch is depressed, the switch is kept in the operating position. This is convenient when continuous
To release the lock-on button, press and release the trigger switch.
To release the lock-on button, press and release the trigger switch.
operating for extended periods of time is required.
To release the lock-on button, press and release the trigger switch.
To release the lock-on button, press and release the trigger switch.
Hole drilling
When attempting to drill a large diameter hole, it is sometimes best to start with a smaller drill bit then work up to the required size.
When attempting to drill a large diameter hole, it is sometimes best to start with a smaller drill bit then work up to the required size.
When attempting to drill a large diameter hole, it is sometimes best to start with a smaller drill bit then work up to the required size.
This prevents overloading the drill.
This prevents overloading the drill.
When attempting to drill a large diameter hole, it is sometimes best to start with a smaller drill bit then work up to the required size.
This prevents overloading the drill.
This prevents overloading the drill.
WARNING! Many accidents occur because of unforeseeable situations. Please
WARNING! Many accidents occur because of unforeseeable situations. Please
WARNING! Many accidents occur because of unforeseeable situations. Please
pay attention that drilling-out a small hole may cause the drill bit to jam in the
pay attention that drilling-out a small hole may cause the drill bit to jam in the
WARNING! Many accidents occur because of unforeseeable situations. Please
pay attention that drilling-out a small hole may cause the drill bit to jam in the
hole, especially when drilling metal.
hole, especially when drilling metal.
pay attention that drilling-out a small hole may cause the drill bit to jam in the
hole, especially when drilling metal.
hole, especially when drilling metal.
Remember to use a "wood-pecker" action on deep holes to allow the swarf to be ejected from the hole.
Remember to use a "wood-pecker" action on deep holes to allow the swarf to be ejected from the hole.
Remember to use a "wood-pecker" action on deep holes to allow the swarf to be ejected from the hole.
If the drill bit snags, swit
If the drill bit snags, swit
Remember to use a "wood-pecker" action on deep holes to allow the swarf to be ejected from the hole.
If the drill bit snags, swit
A
Try running the drill in reverse to remove the bit.
Try running the drill in reverse to remove the bit.
If the drill bit snags, swit
Try running the drill in reverse to remove the bit.
Keep the drill in line with the hole. Ideally, the drill bit should enter at right angles to the work. If the angle is changed during drilling, this could cause
Keep the drill in line with the hole. Ideally, the drill bit should enter at right angles to the work. If the angle is changed during drilling, this could cause
Try running the drill in reverse to remove the bit.
Keep the drill in line with the hole. Ideally, the drill bit should enter at right angles to the work. If the angle is changed during drilling, this could cause
the bit t
the bit t
the bit t
Keep the drill in line with the hole. Ideally, the drill bit should enter at right angles to the work. If the angle is changed during drilling, this could cause
Reduce pressure as the drill is about to break through the item being drilled.
Reduce pressure as the drill is about to break through the item being drilled.
the bit t
Reduce pressure as the drill is about to break through the item being drilled.
Don't force the drill, let it work at its own pace.
Don't force the drill, let it work at its own pace.
Reduce pressure as the drill is about to break through the item being drilled.
Don't force the drill, let it work at its own pace.
Keep the drill bit sharp.
Keep the drill bit sharp.
Don't force the drill, let it work at its own pace.
Keep the drill bit sharp.
Keep the drill bit sharp.
Drilling wood
For maximum performance when drilling larger holes, use auger bits or spade bits for wood drilling.
For maximum performance when drilling larger holes, use auger bits or spade bits for wood drilling.
For maximum performance when drilling larger holes, use auger bits or spade bits for wood drilling.
Begin drilling at a very low speed to prevent the bit fr
Begin drilling at a very low speed to prevent the bit fr
For maximum performance when drilling larger holes, use auger bits or spade bits for wood drilling.
Begin drilling at a very low speed to prevent the bit fr
When drilling through holes, place a block of wood behind the work piece to prevent ragged or splintered edges on the back of the hole.
When drilling through holes, place a block of wood behind the work piece to prevent ragged or splintered edges on the back of the hole.
Begin drilling at a very low speed to prevent the bit fr
When drilling through holes, place a block of wood behind the work piece to prevent ragged or splintered edges on the back of the hole.
When drilling through holes, place a block of wood behind the work piece to prevent ragged or splintered edges on the back of the hole.
Drilling metal
For maximum performance, use HSS drill bits for metal drilling.
For maximum performance, use HSS drill bits for metal drilling.
For maximum performance, use HSS drill bits for metal drilling.
centre of the hole using a centre punch.
centre of the hole using a centre punch.
For maximum performance, use HSS drill bits for metal drilling.
centre of the hole using a centre punch.
Use a suitable lubricant for the material you are working on.
Use a suitable lubricant for the material you are working on.
centre of the hole using a centre punch.
Use a suitable lubricant for the material you are working on.
Begin drilling at a very low speed to prevent the bit fr
Begin drilling at a very low speed to prevent the bit fr
Use a suitable lubricant for the material you are working on.
Begin drilling at a very low speed to prevent the bit fr
Always clamp sheet metal. Support thin metal with a block of wood to avoid distorting it.
Always clamp sheet metal. Support thin metal with a block of wood to avoid distorting it.
Begin drilling at a very low speed to prevent the bit fr
Always clamp sheet metal. Support thin metal with a block of wood to avoid distorting it.
Always clamp sheet metal. Support thin metal with a block of wood to avoid distorting it.
ately to prevent permanent damage to the drill.
ately to prevent permanent damage to the drill.
ately to prevent permanent damage to the drill.
ately to prevent permanent damage to the drill.
king the hole and perhaps causing injury.
king the hole and perhaps causing injury.
king the hole and perhaps causing injury.
king the hole and perhaps causing injury.
rting point. Increase the speed as it bites into the wood.
rting point. Increase the speed as it bites into the wood.
rting point. Increase the speed as it bites into the wood.
rting point. Increase the speed as it bites into the wood.
rting point.
rting point.
rting point.
rting point.
256 193
FR
ES
PT
IT
EL
PL
UA
RO
EN