Publicité
Les langues disponibles
Les langues disponibles
Safety / General Information
READ AND FOLLOW
SAFETY INSTRUCTIONS!
Carefully read and follow all safety instructions in this
manual and on pump.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
warns about hazards that will cause seri-
ous personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
DESCRIPTION
These Submersible Utility Pumps are designed for drain-
ing water from basement floors, stock tanks, window
wells, boats, flat roofs and cisterns. The units are
equipped with a 3-prong grounding-type power cord. The
shaded-pole motors are oil filled and sealed for cooler
operation. The sleeve bearings on the motor shaft never
need lubrication. Automatic reset thermal protection.
Pump water only with this pump.
NOTICE: This unit is not designed as a waterfall or foun-
tain pump, or for applications involving salt water or
brine! Use with waterfalls, fountains, salt water or brine
will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required...............................115V, 60 HZ.
Liquid Temp. Range .................. Less Than 120°F (50°C)
Individual Branch Circuit Required (min.).........15 Amps
Discharge: .....................................................1-1/4" NPT
Risk of fire or explosion. Do not use in
explosive atmospheres. Pump water only with this pump.
PERFORMANCE
GPH (LPH) AT TOTAL FEET (M)
Model
0
5
No.
(0)
(1.5m)
CAPACITY GALLONS(L)/Hour
SDSU4
1,320
1,170 1,020
(4,997) (4,429) (3,861) (3,066) (1,931) (7.6m)
SDU25-01 2,160
1,740 1,620
(8,160) (6,600) (6,120) (4,790) (2,700) (7.9m)
For parts or assistance, call SHUR-DRI Customer Service at
10
15
20
Max.
(3m)
(4.6m) (6.1m) Lift
810
510
25 ft.
1,260
720
26 ft.
ELECTRICAL & SWITCH
SPECIFICATIONS
Model
No.
HP
SDSU4
1/4
SDU25-01
1/3
GENERAL SAFETY INFORMATION
Electrically powered utility pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. See the "Troubleshooting Chart"
in this manual for information about common utility
pump problems and remedies. For more information, see
your retailer, or call SHUR-DRI customer service at
1-800-535-4950.
1. Know the pump application, limitations, and poten-
tial hazards.
2. Do not use this pump in water with fish present. If any
oil leaks out of the motor it can kill fish.
3. Disconnect the power before servicing.
4. Release all the pressure within the system before ser-
vicing any component.
5. Drain all the water from the system before servicing.
6. Secure the discharge line before starting the pump.
An unsecured discharge line will whip, possibly caus-
ing personal injury and/or property damage.
7. Check hoses for a weak or worn condition before each
use, making certain that all connections are secure.
8. Periodically inspect the pump and the system compo-
nents. Keep free of debris and foreign objects.
Perform routine maintenance as required.
9. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly
lighted – replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks, mas-
ter switches, and by removing starter keys.
11. When wiring an electrically driven pump, follow all
of the electrical and safety codes that apply.
12. This equipment is only for use on 115 volt (single
phase) and is equipped with an approved 3-conduc-
tor cord and 3-prong, grounding-type plug. If you
use an extension cord, it must be a 3-wire cord with
3-prong, grounding-type plug, and must be at least 16
AWG, not more than 25' long.
1-800-535-4950
Motor
Individual
Full Load
Branch Circuit
Amps
Req. (Amps)
6.0
10
10.0
15
2
Publicité
