Pioneer VSX-832 Mode D'emploi page 56

> Before Start > Part Names
Front Left After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Center After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (P46) matches the
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Front Right After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Height Left After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (P46) matches the
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
56
> Install > Initial Setup > Playback
Advanced Setup
Height Right After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (P46) matches the
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Surround Right After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (P46) matches the
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Surround Left After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (P46) matches the
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (P47).
Subwoofer After selecting the speaker frequency from between "31 Hz" and
"250 Hz" with the cursors / , adjust the volume of that
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 This cannot be selected if "No" is set in "System Setup" -
"Speaker" - "Configuration" - "Subwoofer" (P46).
0 The result may not be as expected depending on the input source and listening mode
| Supplementary Information | Others