Publicité
Les langues disponibles
Les langues disponibles
> Before Start
> Part Names
Front Left
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Center
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Front Right
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Height Left
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Height Right
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Surround Right
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Surround Left
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
Subwoofer
Specify the distance between each speaker and the listening
position. (Default Value is "10.0 ft/3.00 m")
0 Default values vary depending on the regions.
0 Distance units can be switched by pressing MODE on the remote controller. When the
unit is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1 ft. When the
unit is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
∫ Channel Level
Front Left
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Center
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Front Right
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
48
> Install
> Initial Setup
> Playback
Advanced Setup
Height Left
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Height Right
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Surround Right
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Surround Left
Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
Subwoofer
Select a value between "-15.0 dB" and "+12.0 dB" (in 0.5 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0.0 dB")
∫ Dolby Enabled Speaker
Dolby Enabled
Set the distance between the Dolby enabled speaker and the
Speaker to Ceiling
ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/
4.50 m" (in 0.1 ft/0.03 m increments, default value is "6.0 ft/
1.80 m")
0 The unit of distance (feet/meters) shown is the unit selected
for use in "Distance".
0 Default values vary depending on the regions.
Reflex Optimizer
You can enhance the reflection effect of Dolby enabled speaker
from the ceiling.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 The function is not effective if the listening mode is Pure
Direct.
0 This setting can only be selected when you have set "Configuration" - "Height Speaker" to
"Dolby Speaker".
| Supplementary Information | Others
Publicité
Chapitres
Dépannage
