Battery Capacity Indicator - EINHELL CE-JS 8/1 Instructions D'origine

The temperature of the battery pack may rise
slightly during the charging operation. This is
normal.

5.2 Battery capacity indicator

Press the ON/OFF button (Fig. 1/Item 6) briefl y.
The LED for the battery capacity indicator (Fig. 1
/ Item 7) light up. The number of LEDs that are lit
indicate the current charge level of the integrated
Li-Po battery.
100% charged = 4 LED steady on
>25% charged = 1 LED steady on
<25% charged = no LED steady on
5.3 Time limits
To protect the integrated battery cells, the LED
light will switch off after being in use for approx.
3 hours.
6. LED lamp
Caution! Do not look into the light beam.
•
Press the ON/OFF button for 3 seconds – the
LED lamp (Fig. 1 / Item 1) will be permanently
lit.
•
Press the ON/OFF button again – the LED
lamp will be lit as a „strobe light".
•
Press the ON/OFF button again – the LED
lamp will be lit as an „SOS" Morse code sig-
nal lamp.
•
Press the button again to switch the LED
lamp off again.
7. Outputs
Caution! Check the voltage and current ratings of
the device you want to connect (e.g. mobile pho-
ne, notebook). Observe the operating instructions
for the device.
The supply time varies according to the level of
the charge of the jump start power bank, the level
of power consumption and the intensity of use of
the connected device. The battery needs char-
ging when the remaining charge is 25% (1 LED
shines) (see section 5). If the input current of the
connected device is very low, the equipment will
switch off again within a few seconds. The equip-
ment will also switch off if the integrated battery
is empty.
The USB ports can be used in parallel. Please
ensure that the cumulative output current does
Anl_CE_JS_8_1_SPK9.indb 17 Anl_CE_JS_8_1_SPK9.indb 17
GB
not exceed 5 A.
7.1 Charging/operating devices with a USB
connection
a) 5V/2A USB outlet
1. Connect an available (or the supplied 3-in-1)
USB connection cable to the USB port (Fig.
1 / Item 4) on the jump start power bank and
then to the device you want to connect (max.
2A).
2. Press the ON/OFF button (Fig. 1 / Item 6).
b) "OUT 5V/9V" USB outlet
Note: If charging does not work with this outlet,
this means that either the device or the cable is
not supported. In this case, use the 5V d.c. / 2A
USB outlet for charging, as described above.
1. Connect the supplied 3-in-1 USB cable (Fig.
2) to the "OUT 5V/9V" USB port (Fig. 1 / Item
3) on the jump start power bank and then to
the device you want to connect.
2. Press the ON/OFF button (Fig. 1 / Item 6).
3. The parameters required for charging will be
determined at the USB outlet and the connec-
ted device will be charged up. Depending on
the charger cable and the device being char-
ged, the charging time with the "OUT 5V/9V"
USB outlet may be shorter than with the "OUT
5V/2A" USB outlet.
8. Jump starting for the vehicle
The 12 V jump starting function provides welcome
help with starting diffi culties due to too little batte-
ry capacity.
Warning! Only the jump start cable is allowed
to be connected during jump starting. Any power
supply to a connected device, e.g. via the USB
port, must be disconnected fi rst.
•
Consult the vehicle's operating manual for
information about jump starting. Non-obser-
vance can lead to damage to the vehicle.
•
Switch off all power consumers on the vehicle
(headlights, radio, ...). Never try to start a ve-
hicle without a connected starter battery.
•
Make sure that the connector on the jump
start cable is securely connected to the de-
vice socket. If the connection is loose during
jump starting, the connector could melt as a
result of the high current.
•
The poles on the vehicle battery must be
- 17 -
08.02.2021 08:43:17 08.02.2021 08:43:17